Wind & Solar FT-300 User Manual Download

Page: 2 / 46

Introduction

Thank you for your purchase of the FT0300

Professional WIFI Wireless Weather station

. The following user

guide provides step by step instructions for installation, operation and troubleshooting.

Warnings

Warning:

Any metal object may attract a lightning strike, including your weather station mounting pole.

Never install the weather station in a storm.

Warning:

Installing your weather station in a high location may result in injury or death. Perform as

much of the initial check out and operation.

Getting Started

The FT0300 weather station consists of a display console (receiver), a sensor array with Integrated Outdoor
Transmitter and mounting hardware.

Parts List

The FT0300 weather station consists of the following parts (as referenced in Figure 1).

QTY

Item

Image

Display Console
Frame Dimensions (L x H x W): 215 x 22 x 158mm
LCD Dimensions (L x W): 170 x 125mm

Integrated Outdoor Transmitter
Dimensions (L x H x W)

：

330 x 150 x 280mm

Summary of Contents for FT-300















































Search results

Summary of Contents for FT-300

Reviews:

Related manuals for FT-300

Brands by name

Popular brands

Wind & Solar FT-300, User Manual

Search results

Summary of Contents for FT-300

Reviews:

Related manuals for FT-300

Brands by name

Popular brands