background image

7

OPM-140/E

PREPARING THE UNIT 

UNPACKING

CAUTION: EQUIPMENT DAMAGE

THIS UNIT HAS BEEN SHIPPED WITH OIL. Failure to 

maintain the engine oil at the proper level will result in 

serious engine damage.

When you unpack your engine-generator set be sure to 

remove all the information sheets and manuals from the 

carton.

1. As you receive your unit, it is critical to check it for any 

damage. If any damage is noted, it is always easiest to 

refuse the shipment and let WINCO take care of the freight 

claim. If you sign for the unit, the transfer of the ownership 

requires that you file the freight claim

2. Before proceeding with the preparations of your new 

generator for operation, take a couple of minutes to ensure 

the unit you have received is the correct model and review 

the specification pages in this manual to ensure that this 

unit meets your job requirements.

LUBRICATION

Before starting the engine, check the oil level. This unit has 

been shipped with oil. The recommended grade oil and 

quantity of oil required is listed in the engine operator’s 

manual and under the service tab in this manual. This unit 

was shipped with most of the oil removed. The engine 

normally holds 73.6 ounces (2.3 quarts) of oil. Since there is 

some trapped in the engine, when filling the crankcase the 

first time, use the dipstick to ensure that you do not over 

fill the crankcase. The full oil level mark on the dipstick is 

depicted in the following image.

Oil is added to the engine by removing the oil cap and 

adding oil at this point. After filling the crankcase to the 

proper level, be sure you properly tighten the oil fill cap. 

NOTE: This engine generator must be on a level surface 

before you check or add oil to the system.

The necessity of using the correct oil and keeping the 

crankcase full cannot be overemphasized. Engine failures 

resulting from inadequate or improper lubricant are 

considered abuse and not covered by the generator or 

engine manufacturer’s warranty.

OIL RECOMMENDATIONS

Outdoor temperatures determine the proper oil viscosity for 

the engines. Winco recommends our 5W-30 fully synthetic 

oil to give you excellent protection in cold temperatures 

while maintaining excellent performance in warmer 

weather.

OIL ALERT SYSTEM

This generator is equipped standard with the Briggs & 

Stratton low oil pressure shutdown system. The low oil 

shutdown system is designed to prevent severe damage 

caused by an insufficient amount of oil in the crankcase. 

However, if the unit is repeatedly allowed to shutdown on 

low oil pressure, progressive damage will be done to the 

engine, shortening the engine’s life. The engine switch will 

remain in the “ON” position when the unit is shutdown by 

the low oil pressure system.

 

CAUTION: EQUIPMENT DAMAGE

Allowing the engine to shutdown repeatedly on low oil 

level may cause excessive wear which can be cumulative. 

GASOLINE

When using gasoline, always use fresh, clean, unleaded 

fuel. The engine is certified to operate on unleaded gasoline 

with a minimum octane rating of 87 or higher. Gasoline 

containing no more the 10% ethanol is acceptable.

CAUTION: EQUIPMENT DAMAGE

Do not use unapproved gasolines, such as E15 or E85. 

Do not mix oil in the gasoline. Use of unapproved fuels 

will damage the engine components and void the engine 

warranty.

Use of fuels with content of ethanol greater than shown 

above may cause starting and/or performance problems. 

Always ensure that the fuel is clean and free of all 

impurities.

WARNING: FIRE DANGER

Gasoline and its fumes are VERY explosive when proper 

precautions are not taken.

Summary of Contents for WL22000VE





















Reviews: