Winco W100PTO Owner'S Manual Download Page 2

Read and understand all instructions in this
manual before starting and operating the
generator set.

USING THIS MANUAL

Congratulations on your choice of a Winco generator set.

You have selected a high-quality, precision-engineered
generator set designed and tested to give you years of
satisfactory standby service.

To get the best performance from your new generator

set, it is important that you carefully read and follow the
operating instructions in this manual.

Should you experience a problem please follow the

“Things To Check” near the end of this manual. The warranty
listed in this manual describes what you can expect from
WINCO should you need service assistance in the future.

TABLE OF CONTENTS

INTRODUCTION

i

GUIDE TO PRODUCT SAFETY

1

DESCRIPTION

2

PREPARING THE UNIT

2

Unpacking the unit

2

Specifications

2

Assembly

2

INSTALLATION

Foundation Mounting

3

Trailer Mounting

3

ELECTRICAL CONNECTIONS

4

OPERATION

5

Pre-Start Checks

5

Starting    Procedure

6

Stopping

6

 MAINTENANCE

7

Lubrication

7

Cleaning

8

Storage

8

Trouble Shooting Table

8

GENERATOR CONNECTIONS

120/240 Volt Single Phase

10

120/240 Volt Three Phase

10

120/208 Volt Three Phase

11

277/480 Volt Three Phase

11

GENERATOR RECEPTACLE PANELS

12

Convenience Receptacle Wiring

13

36 MONTH WARRANTY

14

PROPER USE AND INSTALLATION

You must be sure your new generator set is:
*

Properly serviced before operating

*

Operated in a well ventilated area

*

Exhaust gases are dispersed safely

*

Wired by a qualified electrician

*

Operated only for its designed purposes

*

Used only by operators who understand its operation

*

Properly maintained

COPY YOUR MODEL AND SERIAL NUMBER HERE

No other WINCO generator has the same serial number as
yours.  It is important that you record the number and other
vital information here, if you should ever need to contact us on
this unit it will help us to respond to your needs faster.

MODEL____________________________________

SERIAL NUMBER____________________________

PURCHASE DATE____________________________

DEALER___________________________________

Summary of Contents for W100PTO

















Reviews: