manualshive.com logo in svg

Wilson Electronics BAIARDO, Operator'S Manual, Page: 19 / 20

Share
Download
Wilson Electronics BAIARDO Operator'S Manual Download Page 19

®

 

34

Trouble Shooting

Error codes will be displayed when a problem occurs. The most 
common error codes and recommended solution are listed in the table 
with other common problems and solutions. ALL error codes can be 
found at www.wilson.com/baiardo along with advance service and 
trouble shooting solutions.

Many error codes can be solved by turning off the machine, 
check connections and restarting.

PROBLEM

SOLUTIONS

Baiardo

®

 will not turn on

Check that machine is plugged into wall outlet

Check that power supply is fully connected and LED on power 
supply is solid green

Remove electronics box and check that all 3 connections are made

Power supply LED is off or 
fl ashing green

The power supply has a short circuit or is dead
Call dealer for a new power supply

Baiardo

®

 is running in the 

wrong language 

Reset language (see page 5)

“Manual mode” is displayed 
at start up 

Check that there is a good connection between bottom 
and top of machine (2 wires)

Remove electronics box and check that all 3 connections are made

If machine was stored in extreme cold, allow several hours for machine 
to warm to room temperature  

Touch screen appears dark/hard 
to read.

Touch screen to activate backlight. This is an energy saving feature  

Puller head does not move when 
activator switch is pressed 

The puller will only activate when the main stringing screen is displayed

Check that the wire on bottom of puller is connected (see page 33) 

Baiardo

®

 is not stable 

Move the machine to level surface

Adjust leveling screws in fl oor plate

String slips through clamp teeth

Adjust clamp (see page 8) 

Clean inner surface of clamp to remove build-up of lubrication from string

10.1   TROUBLE 
  

SHOOTING

 

35

PROBLEM

SOLUTIONS

String slips through puller

Adjust puller (see page 9) 

Clean inner surface of puller to remove build-up of lubrication from string

Clamp base slips on glide rail 
when “locked” 

Adjust clamp base (see page 8)

Clean glide rail 

Remove clamp base from glide rail (see page 32) and clean brass plug 
that normally sits below glide rail  

String tension seems lower 
than normal

Check that string is not slipping through clamps 

Calibrate machine (see page 26)

String seems tighter than normal

Calibrate machine

Clamps leave white marks 
on string

This is normal on some multifi lament strings. 
Clean and adjust clamps to slightest pressure that still grabs string 

Be sure to adjust clamps for different diameters of string

The hex key set is lost

The hex keys are standard metric set and can be purchased at any tool shop

The power cord is lost

The cord from the power brick to the wall is a standard cord used 
on many electronics devices such as computers, projectors, etc.  

A replacement can be found at many electronics stores

Touch screen glass is cracked 
or broken and will not work  

The machine can be run from the buttons above and below the touch screen

An error code is displayed 
on the screen

Turn off the machine, wait several minutes and restart 

Turn off. Check all connections from base to top (2 wires). Remove ECU
box and check all connections (3 wires),  replace electronics box and restart

Go to www.wilson.com/baiardo where all error codes are listed 

Call Wilson. Be sure to have noted the number of the error code

Summary of Contents for BAIARDO





















Reviews:

No comments