Wilson Electronics 271265 Installation Manual Download Page 11 | Manualshive

Page: 11 / 20

Wilson Electronics 271265 Installation Manual Download Page 11

9

10

Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660

or email: [email protected]. Hours: 7 am to 6 pm MST.

Installing a Wilson Electronics Signal Booster

Select a location to install the signal booster that is away from

excessive heat, direct sunlight, moisture and that has proper

ventilation . Do not place the signal booster in an air-tight

enclosure .

Recommended installation locations for in-building signal boosters

are:

• On a shelf

• In a closet

• Near a power outlet.

Note:

It is important to have adequate air ventilation. Maintain

at least 6 inches of clearance from surrounding objects.

Run the

outside antenna cable to the signal booster and attach it to the

connector labeled “outside antenna” on the signal booster . Run

the inside antenna cable to the signal booster and attach it to the

connector labeled “inside antenna” on the signal booster .

Note:

Be careful when

plugging the connector in to

avoid bending the center pins

on the connectors.

DB Pro™

«
...
9
10
11
12
13
...
»

Summary of Contents for 271265





















Reviews:

No comments