background image

© Wikora GmbH 

Page 1                  

 

 

 

          Status: 27.04.2015 

 

                                                                                                                                                                       Errors excepted.        

 

 

WIKORA GmbH 

89568 Hermaringen 

Phone: (07322) 9605-0 

Fax: (07322) 9605-30 

E-mail: [email protected] 

 

Installation manual 
On roof mounting/  
Flat roof mounting

 

Flat plate collectors 
 

 
 
 
 
 

 

 

Wikosun 2010 / 2510 

 

 

Installation  and  commissioning  should  be 
undertaken by a specialist. 

General  terms  and  conditions  of  warranty  state  that 
all  installations  must  be  performed  by  a  suitably 
trained and qualified plumber by taking into account 
local norms and regulations. 

Factory  warranty  will  only  be  covered  if  the 
installation instructions are followed. 

Warranty  does  not  cover  any  damages,  caused  by 
non-observance of this manual. 

The  correct  functioning  is  only  guaranteed  if  the 
installation instructions are followed.  

The  system  is  to  be  checked  annually  by  a 
specialized  company.  Independently,  occurring 
defects must be repaired immediately. 

This  document  should  be  handed  over  to  the 
client on completion of works. 

 

 

 

 

 

 

Index 

1 Transport and storage of collectors ........................................................................................................................... 3

 

2  Mounting accessories ............................................................................................................................................... 3

 

3 Installation .................................................................................................................................................................. 5

 

4 Planning and layout data for collectors .................................................................................................................... 12

 

5 Technical data .......................................................................................................................................................... 13

 

6 Safety instructions .................................................................................................................................................... 13

 

7 General operation and maintenance instruction ...................................................................................................... 14

 

8 Solar fluid ................................................................................................................................................................. 15

 

9 Warranties ............................................................................................................................................................... 17

 

10 Installation and maintenance record ...................................................................................................................... 18

 

 

 

 

Summary of Contents for Wikosun 2010




















Reviews: