WIA MC104-0 Operator'S Manual Download Page 18

Operators Manual

16 

Trusted by the best

12  

Warranty Information

WIA Weldmatic MIG &  
Weldarc MMA Equipment

2 Year Warranty Statement

Welding Industries of Australia (WIA) 
warrants to the original retail purchaser 
that the Weldmatic welding machine 
purchased (Product) will be free from defects 
in materials and workmanship for a period 
of 2 years from the date of purchase of 
the Product by the customer. If a defect in 
material or workmanship becomes evident 
during that period, Welding Industries of 
Australia will, at its option, either:

•  Repair the Product (or pay for the costs 

of repair of the Product); or

•  Replace the Product.

In the event of such a defect, the customer 
should return the Product to the original 
place of purchase, with proof of purchase, 
or contact Welding Industries of Australia on 
1300 300 884 to locate an authorised service 
agent.

Any handling and transportation costs 
(and other expenses) incurred in claiming 
under this warranty are not covered by this 
warranty and will not be borne by Welding 
Industries of Australia. Welding Industries of 
Australia will return the replacement product, 
if original found to be faulty, freight free to 
the customer.

This warranty covers the Weldarc power 
source only, and does not extend to the 
accessories included in the original purchase 
package.

The obligation of Welding Industries of 
Australia under this warranty is limited to the 
circumstances set out above and is subject to:

•  The customer being able to provide 

proof of purchase of the Product and the 
purchase price paid for the Product;

•  The relevant defect in materials or 

workmanship;

•  The Product not having been altered, 

tampered with or otherwise dealt with 
by any person in a manner other than 
as intended in respect of the relevant 
Product; and 

•  The Product not having been used or 

applied in a manner that is contrary to 
customary usage or application for the 
relevant Product or contrary to any stated 
instructions or specification of Welding 
Industries of Australia.

Summary of Contents for MC104-0





















Reviews: