background image

DEHUMIDIFIERS

DEHUMIDIFIERS

-11-

The quick connector into 

the socket on the connector

Quick connection to draining tube

( 4 ) Set unit control as desired and energize.

3 ) Firmly insert power cord into socket on top back of unit.

SuperDry  90

Maintenance and Repair

1. Exterior Cleaning

Use a soft, slightly damp cloth to wipe the plastic body.

a. Remove the inlet grille to access the filter

2. Filter cleaning

18’prior to reaching final drain location.

-10-

Ducting of the unit allows conditioning of an adjacent room or focusing discharge in 

an area needing focused attention.  Diameter for supply ducting is 6”. Flex or layflat 

ducting can be used for this purpose.

9.Optional Duct Installation

SuperDry  90

Preparing the Unit for Use

( 1 )  Position the machine for a minimum  8”clearance on front and sides. Rear of 

machine should be positioned for maximum discharge distance or directly towards a 

specific location for spot drying.

If the unit was moved in such a manner that the compressor didn’

t remain in a 

vertical  orientation, wait a minimum of 30 minutes before turning the unit“on.”

( 2 ) The included drain line attaches to the unit via a quick connection type fitting 

located on the base of the unit.The drain line should be routed to a suitable drain or 

outside.  Because the unit features an integral drain pump, drain line may go vertically up 

Summary of Contents for SuperDry 90













Reviews: