background image

14

Model Snow Boss 721

Ref. No.

Part No. 

Description

1.

629-0236

Extension Cord

2.

710-0157

Hex Bolt 5/16-24 x 0.75”

3.

710-0409

Hex Bolt 5/16-24 x 1.75”

4.

710-0502A

TT Sems Screw

5.

710-0751

Hex Screw 1/4-20 x 0.620”

6.

710-1003

B Screw #10-16 x 0.625” 

7.

710-3013

Hex Screw 1/4-20 x 0.50”

8.

712-3006

Hex Nut 1/4-20

9.

719-0581

Spacer

10.

726-0205

Hose Clamp

11.

731-2005

Choke Knob

13.

736-0119

Lock Washer

14.

736-0242

Beleville Washer

15.

736-0329

Lock Washer

16.

741-0475

Plastic Bushing

17.

751-0535

Fuel Line Hose

18.

751-0540A

Gas Tank

19.

751-0603

Fuel Cap

20.

754-0101A

V-Belt

21.

756-0416B

V-Pulley Half

22.

756-0475

Pulley

23.

784-0322

Engine Mount

24.

784-0323

Support Bracket

25.

784-0374

Support Plate: Engine Mount 

Ref. No.

Part No. 

Description

1

2

3

4

5

6

7

8

9

10

11

13

14

15

13

3

15

16

17

18

19

20

21

22

23

24

25

Engine is for reference only
and may not resemble the 
engine on your snow thrower.

Part of electric
start engines

NOTE: 

For

 painted parts

, please refer to the

list of color codes below. Please add the
applicable color code, wherever needed, to the
part number to order a replacement part. For
instance, if a part, numbered 700-xxxx, is
painted Red Metalic,  the part number to order
would be 700-xxxx-0650.

Red Metallic:  0650

Powder Black: 0637

Summary of Contents for Snow Boss 721

















Reviews: