33740-11-0816
Page 57
NOTE
It is normal for appliances fabricated of steel to give off some
expansion and/or contraction noise during the start up or
cool down cycle. Similar noises are found with your furnace
heat exchanger or car engine.
,WLVQRUPDOIRU\RXUJDV¿UHSODFHWRJLYHRIIVRPHRGRUWKH
¿UVWWLPHLWLVEXUQHG7KLVLVGXHWRWKHFXULQJRIWKHSDLQW
and any undetected oil from the manufacturing process.
Please ensure that your room is well ventilated - open all
windows.
,W LV UHFRPPHQGHG WKDW \RX EXUQ \RXU ¿UHSODFH IRU DW OHDVW
VL[KRXUVWKH¿UVWWLPH\RXXVHLW,IRSWLRQDOIDQNLWKDVEHHQ
installed, place fan in the “OFF” position during this time.
IMPORTANT:
Turn off gas before servicing appliance. It is
UHFRPPHQGHGWKDWDTXDOL¿HGVHUYLFHSHUVRQSHUIRUPWKHVHFKHFN
ups once a year preferably before the using of the appliance.
&OHDQ%XUQHUDQG&RQWURO&RPSDUWPHQW
Keep the control compartment and burner area clean by vacuuming
or brushing at least twice a year.
Cleaning Procedure
1. Turn off unit.
2. Remove offset frame and glass front. See Glass Removal.
3. Remove logs and embers.
4. Vacuum burner compartment (a clean portable shop-vac is
recommended).
5. Replace logs and embers.
6. Reinstall glass front and offset frame.
7. Ignite unit. See Lighting Instructions.
,IÀDPHDSSHDUVDEQRUPDOFDOODVHUYLFHSHUVRQ
&KHFN9HQW6\VWHP
The appliance and venting system should be inspected before
LQLWLDOXVHDQGDWOHDVWDQQXDOO\E\DTXDOL¿HGVHUYLFHSHUVRQ
Inspect the external vent cap on a regular basis to make sure
WKDWQRGHEULVLVLQWHUIHULQJZLWKWKHDLUÀRZ
Glass Cleaning
It will be necessary to clean the glass periodically. During start-up
condensation (which is normal) forms on the inside of the glass
and causes lint, dust and other airborne particles to cling to the
JODVVVXUIDFH$OVRLQLWLDOSDLQWFXULQJPD\GHSRVLWDVOLJKW¿OPRQ
the glass. It is recommended that the glass be cleaned two or three
times with a non-abrasive household cleaner and warm water (we
UHFRPPHQGJDV¿UHSODFHJODVVFOHDQHU$IWHUWKDWFOHDQWKHJODVV
two or three times during each season or more often if necessary.
General Glass Information
WARNING
Do not operate appliance with the glass front removed, cracked
or broken.
2QO\JODVVDSSURYHGIRUXVHE\WKHPDQXIDFWXUHULQ¿UHSODFHPD\
be used for replacement. The glass replacement should be done
E\DOLFHQVHGRUTXDOL¿HGVHUYLFHSHUVRQ
MAINTENANCE AND SERVICE
WARNING
1. The use of substitute glass will void all product warranties.
2. Care must be taken to avoid breakage of the glass.
3. Under no circumstances should this appliance be operated
without the glass front or with a broken glass front.
Replacement of the glass (with gasket) as supplied by the
PDQXIDFWXUHUVKRXOGEHGRQHE\DTXDOL¿HGVHUYLFHSHUVRQ
4. Do not abuse the glass by striking or hitting it.
WARNING
Do not use Ammonia based or abrasive cleaners on glass. Do
not attempt to clean glass when glass is hot.
Glass and Offset Frame Removal and Replacement
1.
The glass latch tool is shipped with the unit attached to the left
hand side, and may be stored on a hook inside the left hand
VLGHRIWKH¿UHER[FDYLW\
See Figure 83.
2.
To remove the offset frame; release tabs in the upper corners by
ÀH[LQJWKHPDZD\IURPWKHJODVVIUDPH7LOWRIIVHWIUDPHWRWKH
left or right in order to access one of the bottom tabs. Release
tab and remove offset frame.
See Figure 84.
Installation is the
reverse of removal.
NOTE
: If no decorative front accessory is being installed, the four
shoulder bolts on the offset frame may be removed.
NOTE
7KHJODVVIUDPHLVKHOGRQWRWKH¿UHER[ZLWKVL[JODVVIUDPH
latches. Only the sides and top latches need to released with
the glass frame tool in order to remove the glass frame.
3. Use the glass latch tool to grip the latch bar and pry it over the
JODVVIUDPHKRRNÀDQJHV
See Figure 85.
4. Tilt the glass frame towards you and pull upwards to remove
from the unit.
7RUHSODFHJODVVIUDPHVHWJODVVIUDPHERWWRPÀDQJHLQWRWKH
bottom latch bars. Tilt the glass frame towards the unit. Use
glass latch tool to pull the remaining four latch bars out and
RYHUWKHJODVVIUDPHKRRNÀDQJHV
