White Mountain Hearth 42)FP30(N Installation Instructions And Owner'S Manual Download

Page: 52 / 68

35009-2-1015

Page 52

INTERMITTENT PILOT ELECTRONIC SYSTEM OPERATING INSTRUCTIONS

The electronic control valve system includes the ability to switch

the pilot from a standing pilot mode to an intermittent pilot mode.

•

IPI Mode

- In the Intermittent Pilot mode when the unit is

turned ON, it will cause spark to the pilot, light the pilot,

then allow the burner to light. When the unit is turned

OFF, both the burner and pilot will turn OFF.

•

CPI Mode

- In Continuous Pilot mode the pilot remains

ON when the burner is turned OFF.

Note: A small toggle switch is located on the front of the module

tray switches from IPI (left) to the CPI (right).

See Figure 62.

When the unit is turned ON, the electrical current will energize a

spark to the pilot igniter. Once the pilot sensor heats up (after a

few seconds), the valve will be energized, allowing gas to flow to

the burner.

1. Follow the SAFETY and LIGHTING INSTRUCTIONS for In-

termittent Pilot controls found in this manual, and on labels

found in the control compartment located in the lower cavity

of the appliance.

2. During the heating season (or in power outage periods), it is

recommended that the pilot remain in the CPI (standing pilot

mode) to reduce cold start issues, and/or conserve battery

backup power during a power outage.

3. The gas valve has inlet and outlet pressure taps as shown in

Figure 62.

Refer to Page 13 for gas pressure requirements.

Note:

The gas control has a manual HI/LO flame adjustment

knob.

See Figure 62.

Rotate the HI/LO knob counter-

clockwise to “HI” to increase the flame height, and clock-

wise to “LO” to decrease the flame height. The BTU

change from HI to LO is 37,000 BTU to 26,000 BTU.

OPTIONAL REMOTE CONTROLS

Optional remote controls are available for use with this appliance.

Place the remote receiver in a wall outlet box with extended wir-

ing, on the fireplace hearth, behind the left side surround panel,

or in the control compartment area as far forward in the insert as

possible.

The placement options for the remote receiver are given to allow

flexibility, however battery life will be extended when the receiver

is placed in a cool area.

To connect the remote receiver to the appliance, first disconnect

the ON/OFF switch wires from the white and green wire connec-

tors and connect the wires from the remote receiver to the green

and white wire connectors. See Page 53.

Follow the instructions included with the remote control for pro-

gramming and operating.

SENSOR

MANUAL
HI/LO
REGULATOR

GAS VALVE

OUTLET
PRESSURE
TAP

INLET
PRESSURE
TAP

MODULE TRAY

9 PIN CONNECTOR

SPARK ROD

GROUND

MANUAL ON/OFF SWITCH
NOTE: ADDITIONAL ON/OFF SWITCH & WIRING INCLUDED

PILOT SELECTOR SWITCH

IPI - INTERMITANT PILOT (LEFT)
CPI - CONTINUOUS PILOT (RIGHT)

AA (4)
BATTERY
BACKUP

PILOT
ASSEMBLY

IGNITOR

Figure 62

Summary of Contents for 42)FP30(N





































































Search results

Summary of Contents for 42)FP30(N

Reviews:

Related manuals for 42)FP30(N

Brands by name

Popular brands

White Mountain Hearth 42)FP30(N, Installation Instructions And Owner'S Manual

Search results

Summary of Contents for 42)FP30(N

Reviews:

Related manuals for 42)FP30(N

Brands by name

Popular brands