White Mountain Hearth 42)FP30(N Installation Instructions And Owner'S Manual Download

Page: 55 / 68

35009-2-1015

Page 55

Components

The gas valve is fitted with a manual HI/LO knob to allow for man-

ual modulation of the gas outlet pressure to the appliance burner.

The controls are designed to be used with either LPG or Natural

Gas and can be converted by use of an OEM supplied conversion

kit.

The Digital Fireplace Control (DFC) is an automatic gas ignition

system based on a single micro-controller core. This control man-

ages all functions related to ignition, flame sensing and supervi-

sion for atmospheric applications.

The DFC can be set to provide continuous or intermittent ignition

control sequences and flame monitoring with safety shutdown in

case of failure.

The DFC is set up as a stand alone (AC powered system with

battery back up. See Lighting Instructions on Page 54 and Wiring

Diagram on Page 53.

This appliance is only for use with the type of gas indicated on

the rating plate in this appliance and may be installed in an after-

market, permanently located, manufactured (mobile) home where

not prohibited by local codes. This appliance is not convertible for

use with other gases, unless a certified kit is used.

WARNING

Improper installation, adjustment, alteration, service or mainte-

nance can cause property damage, personal injury or loss of

life. Installation and service must be performed by a qualified

installer, service agency or the gas supplier.

INTERMITTENT PILOT CONTROL SYSTEM TROUBLESHOOTING

Troubleshooting

Before proceeding with the procedures in the following trouble-

shooting table, verify that the power supply (AC/DC adapter) is

present and that the batteries inside the receiver and/or optional

battery pack are fresh and installed with correct polarity.

Make sure all the connections between the wire harnesses and

system components are proper and positive.

Verify that the static inlet pressure meets the manufacturer’s rec-

ommended inlet pressure. If necessary adjust the line pressure

regulator.

If the recommended actions for the following troubleshooting chart

do not help to address the problem consider replacing wiring har-

nesses.

WARNING

Any actions performed on the gas valve must be in accor-

dance with this instruction manual. Likewise, any actions

performed on the Digital Fireplace Control (DFC) or other

system components must be done in accordance with the

individual component instructions.

Replacement of components must be performed in accor-

dance with this instructions manual.

Summary of Contents for 42)FP30(N





































































Search results

Summary of Contents for 42)FP30(N

Reviews:

Related manuals for 42)FP30(N

Brands by name

Popular brands

White Mountain Hearth 42)FP30(N, Installation Instructions And Owner'S Manual

Search results

Summary of Contents for 42)FP30(N

Reviews:

Related manuals for 42)FP30(N

Brands by name

Popular brands