White Knight CPT-1 Product Manual Download

Page: 19 / 20

Manual Version 1.3.1

Manual Part# 18200-LM-0038

11 Ordering Instructions

(Registered by Galil Motion Control, Inc.)

CPT-1 (Cycle Rate Translator) Ordering Instructions

White Knight Fluid Handling, Inc.

435-783-6040

Optional Configurations

= 44 male pin to 1-

Meter Wire Lead Cable

①

②

CPT-1

To configure your Cycle Rate Translator with different connection methods, a power supply or request a specific revision level,
please select options from the appropriate additional options (1-3).

www.wkfluidhandling.com

③

Revision Level : Contact factory for copy exact code activation information.

Rev

③

= 44 male pin to Screw

Terminals

①

Connection Method

②

Power Supply

= 24V/60W Power

Supply

Required

Configurations

Additional

Options

= Quick Connect Plugs

This pump requires the use of, and comes standard with, quick exhaust valves.

Summary of Contents for CPT-1





















Search results

Summary of Contents for CPT-1

Reviews:

Related manuals for CPT-1

Brands by name

Popular brands

White Knight CPT-1, Product Manual

Search results

Summary of Contents for CPT-1

Reviews:

Related manuals for CPT-1

Brands by name

Popular brands