White Knight CPT-1 Product Manual Download Page 9

Page: 9 / 20

Manual Version 1.3.1

Manual Part# 18200-LM-0038

5.3 Digital Outputs:

The CPT-1 sends out signals to control or be read by other devices. There are two types of digital outputs, voltage

source or a voltage sink. The CPT-1 will turn on both corresponding voltage source and sink when it turns on an

output. Generally, components that may have a higher current draw should be connected to the voltage sink.

Pin Name

Pin #

Wire Color/

Stripe

Designation

Levels

Note

Digital Output:

Left Solenoid

[DO_0]

Orange/
White Stripe

Sink

Relay Open = Not Active
Relay Closed = Active

The CPT-1 will turn

on the left and right

solenoid signals to

control a solenoid-

operated pump. If

using a shuttle-

operated pump

these connections

are not required.

Light Green/
Green Stripe

Source

Relay Open = Not Active
Relay Closed = Active

Digital Output:

Right Solenoid

[DO_1]

Red/
Green Stripe

Sink

Relay Open = Not Active
Relay Closed = Active

White/
Black Stripe

Source

Relay Open = Not Active
Relay Closed = Active

Digital Output:

Left Translated

Cycle Rate

[DO_2]

Light Blue

Sink

Relay Open = Not Active
Relay Closed = Active

This is the output to

tell the tool about

the modified cycle

rate. If the tool is

only looking for one

signal indicating a

full cycle rate, only

connect one of these

to the tool.

Otherwise connect

both left and right to

the tool.

Brown/
White Stripe

Source

Relay Open = Not Active
Relay Closed = Active

Digital Output:

Right Translated

Cycle Rate

[DO_3]

Pink/
Black Stripe

Sink

Relay Open = Not Active
Relay Closed = Active

Light Blue/
Green Stripe

Source

Relay Open = Not Active
Relay Closed = Active

Digital Output:

System On

[DO_4]

Orange/
Green Stripe

Sink

Relay Open = Not Active
Relay Closed = Active

This is to indicate

that the system is

on. This input is

required when

operating a shuttle

pump. However this

can also be used as

verification that the

system is

operational.

Pink

Source

Relay Open = Not Active
Relay Closed = Active

Digital Output:

Leak Alarm

[DO_5]

Gray

Sink

Relay Open = Not Active
Relay Closed = Active

This output is to alert

the user that a leak

was detected.

Violet/
White Stripe

Source

Relay Open = Not Active
Relay Closed = Active

Digital Output:

Over Speed

Alarm

[DO_6]

Light Green/
Black Stripe

Sink

Relay Open = Not Active
Relay Closed = Active

This output is to alert

the user that the

pump was operating

faster than the set

threshold

Brown/
Green Stripe

Source

Relay Open = Not Active
Relay Closed = Active

Digital Output:

Under Speed

Alarm

[DO_7]

Gray/
Green Stripe

Sink

Relay Open = Not Active
Relay Closed = Active

This output is to alert

the user that the

pump was operating

slower than the set

threshold

Light Green

Source

Relay Open = Not Active
Relay Closed = Active

Table 3: List of digital output wiring with designations

Summary of Contents for CPT-1





















Search results

Summary of Contents for CPT-1

Reviews:

Brands by name

Popular brands

White Knight CPT-1, Product Manual

Search results

Summary of Contents for CPT-1

Reviews:

Brands by name

Popular brands