WhisperKool Platinum Split H.E. PS4000 Owner'S Manual Download

Page: 40 / 59

FULLY DUCTED UNIT SPECIFICATIONS

Duct plenum

Return air

Supply air

*Each c

ellar is unique and has specific c

ooling requirements. Heat load calculations should always be performed prior to selecting a cooling unit.

Model

Platinum Split

Ducted

4000

(Fan Coil Unit)

Platinum Split 4000

H.E.

Condenser

(Air-Cooled Condensing Unit)

Dimensions

Refrigerant

R-134a

Condensing Unit HP

Voltage Rating

120V (15-amp dedicated circuit required)

Weight (lbs)

Amps

2.2

Running Amp

Line Set

Liquid line 1/4" OD; Suction line 1/2" OD (less than 50ft.), 5/8" (greater than 50.ft)

Drain Line

1/2” ID clear plastic tubing (not included)

Installation

Evaporator unit is installed in the cellar. Condensing unit can be installed up to 100 line feet from the evaporator unit.

Thermostat

KDT- Advanced digital display (50-ft. cable), liquid-temperature-measuring bottle probe (50-ft. cable), 24V - Customer supplied

Temp. Delta

Can maintain a 55°F cellar temperature with up to 120°F condenser air intake temperature

Warranty

Two-year limited warranty (parts and labor)

BTU/h (60°F condenser air intake

temperature)

Sensible/Total

BTU/h (75°F condenser air intake

temperature)

Sensible/Total

BTU/h (85°F condenser air intake

temperature)

Sensible/Total

463

154

3912

348

766

4096

H.E. Condenser (Air-Cooled

Condensing Unit)

20”L x 20.5”W x 15.5”H

31.18"L x 10.75”W x 21.18"H

220V (15-amp dedicated circuit required)

LRA 10.7, RLA 2.7, FLA 3.1

Cellar Size

000

cu. ft.

Page 38

08/04/21

Summary of Contents for Platinum Split H.E. PS4000




























































Search results

Summary of Contents for Platinum Split H.E. PS4000

Reviews:

Related manuals for Platinum Split H.E. PS4000

Brands by name

Popular brands

WhisperKool Platinum Split H.E. PS4000, Owner'S Manual

Search results

Summary of Contents for Platinum Split H.E. PS4000

Reviews:

Related manuals for Platinum Split H.E. PS4000

Brands by name

Popular brands