manualshive.com logo in svg

Whirlpool WFC7500VW0, User Manual

Share
Download
Whirlpool WFC7500VW0 User Manual Download Page 65

5-1

COMPONENT TESTING

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.

Before testing any of the components, perform 

the following checks:

Control failure can be the result of corrosion 

• 

on  connectors.  Therefore,  disconnecting 

and  reconnecting  wires  will  be  necessary 

throughout test procedures.
All  tests/checks  should  be  made  with  a 

• 

VOM or DVM having a sensitivity of 20,000 

ohms-per-volt DC, or greater. 

Check  all  connections  before  replacing 

• 

components,  looking  for  broken  or  loose 

wires, failed terminals, or wires not pressed 

into connectors far enough.
Resistance checks must be made with pow-

• 

er cord unplugged from outlet, and with wir-

ing harness or connectors disconnected. 
Unless  stated  otherwise,  make  all  resis-

• 

tance checks by disconnecting the compo-

nent connector at the Central Control Unit 

(CCU).

WARNING

Refer  to  page  4-6  for  the  procedure  for  ac-

cessing the inlet cold/bleach water valve.
To check the inlet cold/bleach water valve so-

lenoids at the component terminals, perform 

the following steps.
1.  Unplug washer or disconnect power.
2.  Disconnect the solenoid connector from 

the inlet cold/bleach valve terminals. 

3.  Set the ohmmeter to the R X 100 scale.
4.  Touch the ohmmeter test leads to the 1 

and  2  cold  water  connector  terminals. 

The meter should indicate between 825 

and 1115 Ω.

5.  Touch the ohmmeter test leads to the 1 

and 3 bleach water connector terminals. 

INLET COLD/BLEACH WATER 

VALVE SOLENOIDS

To check the inlet valve solenoids at the CCU, 

perform the following steps.
1.  Unplug washer or disconnect power.
2.  Disconnect the inlet valve solenoid con-

nector 

VPW3 & VW3

 (see page 4-5) from 

the CCU. 

3.  Set the ohmmeter to the R X 100 scale.
4.  Touch the ohmmeter test leads to the fol-

lowing connector pins. The meter should 

indicate between 825 and 1115 Ω.

Pins 1 & 2 (cold)

• 

Pins 1 & 3 (bleach)

• 

1.

DP2

Drain Pump

2.

VPW3 & VW3

Cold / Bleach Valve

3.

VHF3

Hot Valve

4.

M7

Universal Motor

1

2          3

4

1    2    1  2    3      1    2  1    2    3    4  5    6  7

The meter should indicate between 825 

and 1115 Ω.

 COLD

 BLEACH

 1 2 3

Summary of Contents for WFC7500VW0



























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands