manualshive.com logo in svg

Whirlpool WFC7500VW0, User Manual

Share
Download
Whirlpool WFC7500VW0 User Manual Download Page 42

4-6

Electrical Shock Hazard

Disconnect power before servicing.
Replace all parts and panels before    

operating.
Failure to do so can result in death or 

electrical shock.

1.  Unplug washer or disconnect power.
2.   Turn off the water supply to the washer.
3.  Remove the top cover from the washer 

(see page 4-2 for the procedure).

WARNING

REMOVING THE LINE FILTER & POWER SUPPLY CORD

Line Filter

c)  Disconnect  the  three  wire  connectors 

from the line filter. 

NOTE:

 Press and re-

lease the locking arm on the 2-wire con-

nector to disconnect it from the filter. 

5. 

To remove the power supply cord:

a) Remove  the  screw  from  the  green 

ground wire.

b) Pull the connectors with the white and 

black  wires  from  the  line  filter  termi-

nals. 

4. 

To remove the line filter:

a) Remove  the  hex-head  screws  from 

the line filter.

b) Position  the  line  filter  so  that  the  four 

tabs are aligned with the chassis slots 

and remove the filter from the washer. 

Line Filter

4 Tabs

Line Filter Wire 

Connectors

White Wire

Black Wire

Ground Screw

Screws

Summary of Contents for WFC7500VW0



























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands