32
PROBLEM
POSSIBLE CAUSE
REMEDY
The coffee is not hot.
The cups were not preheated.
Warm the cups by rinsing them with hot
water (Please note! you can use the hot water
function).
The infuser has cooled down because
2/3 minutes have elapsed since the
last coffee was made.
Before making the coffee, heat the infuser by
rinsing using the rinse function (see section
“Rinsing
”).
A low coffee temperature is set.
Set a hotter coffee temperature in the menu (sec-
tion “Coffee temperature
”).
The coffee is weak or not creamy
enough.
The coffee is ground too coarsely.
Turn the grinding adjustment dial (A17) one
click anticlockwise towards "1" while the coffee
mill is in operation (fig. 11). Continue one click
at a time until coffee delivery is satisfactory. The
effect is only visible after delivering 2 coffees
(see section “Adjusting the coffee mill”).
The coffee is unsuitable.
Use coffee for espresso machines.
The coffee is delivered too slowly or a
drop at a time.
The coffee is ground too finely.
Turn the grinding adjustment dial (A17) one
click clockwise towards "7" while the coffee mill
is in operation (fig. 11). Continue one click at a
time until coffee delivery is satisfactory. The ef-
fect is only visible after delivering 2 coffees (see
section “Adjusting the coffee mill”).
Coffee does not come out of one or
both of the spouts.
The coffee spouts (A13) are blocked.
Clean the spouts (fig. 31).
The appliance will not make coffee
The appliance has detected impurities
in its internal circuits. "CLEANING UN-
DERWAY" is displayed.
Wait for the appliance to be ready for use again
and reselect the required beverage. Contact
Customer Services if the problem persists.
The appliance does not come on
It is not plugged into the mains socket. Plug into the mains socket (fig. 1).
The main switch (A19) is not turned
on.
Press the main switch (fig. 2).
The infuser cannot be extracted
The appliance has not been turned off
correctly
Turn the appliance off by pressing the
button
(A7) (see section “Turning the appliance off”).
At the end of descaling, the appliance
requests a third rinse
During the two rinse cycles, the water
tank (A12) has not been filled to the
MAX level
Follow the instructions displayed by the appli-
ance, but first empty the drip tray (A14) to avoid
the water overflowing.
The milk does not come out of the
milk spout (D5)
The lid (D2) of the milk container (D)
is dirty
Clean the milk container lid as described in sec-
tion “Cleaning the milk container”.
TROUBLESHOOTING
Below is a list of some of the possible malfunctions.
If the problem cannot be resolved as described, contact Customer Services.
Summary of Contents for W11 CM145
