background image

32

ELECTRONIC CONTROL SETUP INSTRUCTIONS

Diagnostic Codes

If the set-up mode is entered and one of the following has 
previously occurred, the appropriate diagnostic code will be  
in the display.

Dryer Display

Explanation

d 5

Blocked coin 1 or coin drop UI control 
circuit failure (coin recognition and 
customer display disabled while 
blockage persists).

d 9

Voltage detected below 90 VAC for  
8 seconds.

d 13

Blocked coin 2 or coin drop UI control 
circuit failure (coin recognition and 
customer display disabled while 
blockage persists).

d 16

Not receiving communications from 
installed debit card reader in Enhanced 
(Generation 2) Debit mode.

F 01

Dryer motor control circuit error 
(cycles and price display disabled until 
diagnostic code is manually cleared). 
The control doesn’t know if the motor 
relay is bad (stuck on), the motor relay 
drive circuit is bad (shorted), causing 
the motor relay to stay on, or the 
motor relay feedback circuit is bad.

F 22

Exhaust thermistor open, temperature 
drops below 18°F (>50 kΩ) for 1 
minute in Run mode, or immediately  
in Factory Diagnostic Mode.

F 23

Exhaust thermistor shorted, 
temperature above 250°F (<500Ω) for 
1 minute in Run mode, or immediately 
in Factory Diagnostic Mode.

F 70

UI is not receiving communications 
from CCU (cycles and price display 
disabled while error persists or is 
manually cleared).

F 71

CCU is not receiving communications 
from UI (cycles and price display 
disabled while error persists  
or is manually cleared).

F 73

UI Microprocessor is not able to read 
or verify EEPROM (cycles and price 
display disabled until diagnostic code 
is manually cleared).

F 74

UI EEPROM memory is a CRC failure 
(cycles and price display disabled until 
diagnostic code is manually cleared).

Dryer Diagnostic Mode

This mode is entered by pressing COLORS/DELICATES for one 
second while in either of the set-up codes 6.xx or 7.xx or with a 
diagnostic code present. Diagnostic codes are cleared on entry 
and all display segments should flash. If a diagnostic code 
persists, it must be corrected before the diagnostic cycle  
can be entered.

All Models:

With all segments flashing, the diagnostic cycle is started  
by pressing the PERM PRESS button. The cycle consists  
of 7 minutes of heat and 1 minute of cooldown.
The COTTON/WHITES button will increment the diagnostic 
cycle minutes up to 99, then roll over to 2 minutes. The 
COLORS/DELICATES button will cancel this cycle and  
exit the diagnostic mode.

Dryer Help Mode

Dryer help mode is entered by pressing the COTTON/WHITES 
button while in special pricing option 2.XX. In help mode, the 
software revision is displayed. The help mode is advanced by 
pressing the PERM PRESS button. See Help Mode Submenu 
below for the order in which items are displayed. Press the 
COTTON/WHITES button at any time to exit help mode.

Help Codes

Help Code

Description

71

Generation 2 debit card  
cycle polling message out  
of sequence.

74

Generation 2 debit card 
remaining balance message 
out of sequence.

75

Generation 2 debit card new 
card balance message out  
of sequence.

88

Invalid messaging state 
found in data acquisition 
communications comm_
suprv ( ) routine.

Summary of Contents for W10919522B



































Reviews: