background image

2

INSTALLATION INSTRUCTIONS

Tools and Parts

Gather the required tools and parts before starting installation. Read 

and follow the instructions provided with any tools listed here. 

Tools needed:

WARNING: For your safety, the information in this manual must be followed to minimize

the risk of fire or explosion, or to prevent property damage, personal injury, or death.

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this 

or any other appliance.

WHAT TO DO IF YOU SMELL GAS:

Do not try to light any appliance.

Do not touch any electrical switch; do not use any phone in your building.

Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's 

instructions.

If you cannot reach your gas supplier, call the fire department.

Installation and service must be performed by a qualified installer, service agency, or 

the gas supplier.

Clear the room, building, or area of all occupants.

In the State of Massachusetts, the following installation instructions apply:

Installations and repairs must be performed by a qualified or licensed contractor, plumber, or gasfitter qualified or licensed by 

the State of Massachusetts.

If using a ball valve, it shall be a T-handle type.
A flexible gas connector, when used, must not exceed 3 feet.

IMPORTANT: The gas installation must conform with local codes, or in the absence of local codes, with the National Fuel Gas 

Code, ANSI Z223.1/NFPA 54.
The dryer must be electrically grounded in accordance with local codes, or in the absence of local codes, with the National 

Electrical Code, ANSI/NFPA 70.

8" or 10" adjustable 

wrench (for gas 

connections)
Flat-blade screwdriver
Adjustable wrench that 

opens to 1" (25 mm) or 

" (14 mm) open-end 

wrench (for adjusting 

dryer feet)
Level
¼" nut driver or socket 

wrench (recommended)
Tin snips (new vent 

installation)

Caulking gun and 

compound (for installing 

new exhaust vent)
Pipe-joint compound 

resistant to LP gas
Level
Knife
Vent clamps
Pliers
Wood block (for leveling)
Ruler or measuring tape

Parts needed for washer (not provided):

Inlet hoses 

Flat washers 

To order:

Call the dealer from whom you purchased your washer/dryer. 
Call the toll-free number listed on the cover of the Washer/

Dryer User Instructions. 
Visit the website listed on the cover of the Washer/Dryer 

User Instructions.

 

NOTE: 

Replace inlet hoses after 5 years of use to reduce the risk 

of hose failure. Record hose installation or replacement dates for 

future reference.

 

9

16

Summary of Contents for LTG5243DQ - 24" Twin Washer/Dryer Laundry Center













Reviews: