PAGE 3
FOR SERVICE TECHNICIAN’S USE ONLY
DO NOT REMOVE OR DES
TROY
FAULT CODE DISPLAY MODE (Pgs 6–7)
To access fault/error codes, perform steps 1 and 2 of Activating
the Service Diagnostic Test Modes. Turn the cycle selector knob
until the status LEDs correspond as follows:
“Done” LED On
Press the
START
button to enter Fault Code Display Mode.
The status LEDs flash on and off.
1.
To view last 4 fault codes:
Toggle cycle selector knob to view fault codes in the order
of most recent to oldest. (Refer to Fault/Error Code charts
on pages 6 & 7.)
NOTE:
A fault/error code will be removed from memory
if it does not reoccur after 10 consecutive wash cycles.
2.
To clear fault codes:
Toggle cycle selector knob until the status LEDs
flash ON and OFF (see figure 2, page 2).
Press and hold the
START
button for 3 seconds to clear
all fault codes and exit Fault Code Display Mode.
Fault/Error Code Display Method
Fault/error codes are displayed by alternating the state of
the Status LEDs in one second intervals. All fault/error codes
have an F# and an E#. The F# indicates the suspect System/
Category and the E# indicates the suspect Component system.
If the Sensing Load LED is
ON
, the
Fault Number
is represented;
if
OFF
, the
Error Number
is represented (see example below).
The remaining LEDs (Soak/Wash, Rinse, Final Spin, and Done)
represent the fault and error code in binary. (See Fault/Error
Code Charts on pages 6 & 7 for more information.) = ON.
LED names may vary between makes and models.
3.
There are several accessible Diagnostic Test Modes shown
in the chart below. To select the desired Mode of Operation,
toggle the cycle selector knob left and right one click in each
direction, advancing through the Test Modes until the status
LEDs match the mode desired to enter.
4.
Press the
START
button to enter desired mode of operation.
Refer to the following pages for detailed information on each
mode of operation:
FAULT CODE DISPLAY MODE:
Page 3
QUICK OVERVIEW TEST MODE:
Page 4
MANUAL OVERVIEW TEST MODE:
Page 4
CALIBRATION MODE:
Page 4
SALES DEMO MODE:
NOT FOR SERVICE USE*
UI TEST MODE:
Page 4
SW VERSION DISPLAY MODE:
Page 5
FACTORY DIAGNOSTICS:
If accessed, washer must be
recalibrated (see Calibration Mode)
TACHOMETER VERIFICATION MODE:
Page 5
DRY FACTORY DIAGNOSTICS:
Page 5
FACTORY CAL TEST MODE:
Page 5
CLEAN WASHER CYCLE:
Page 5
*To exit, press and hold the
START
button for 3 seconds.
Unsuccessful Entry
If entry into diagnostic test mode is unsuccessful, refer to the
following indication and action:
Indication:
None of the LEDs turn on.
Action:
Press
START
button to enter setting mode.
If indicators come on, repeat steps 1 through 4 of Activating
the Service Diagnostic Modes.
NOTE:
Rotating the dial too
fast or too slow will affect entry.
If no indicators come on after pressing the
START
button,
go to TEST #1, page 12.
EXITING THE SERVICE DIAGNOSTIC
TEST MODES
Press and hold the
START
button for 3 seconds at any time
to exit diagnostic test modes.
Washer will exit diagnostic test modes after 5 minutes of
inactivity or unplugging the power cord.
E
D
O
M
SOAK
/
W
ASH
RINS
E
FINA
L
SPI
N
DONE
Fault Code Display Mode
1
Quick Overview Test Mode
2
Manual Overview Test Mode
2
Calibration Mode
4
Sales Demo Mode
4
UI Test Mode
4
STATUS LEDs
DIAGNOSTIC TEST MODES
SW Version Display Mode
4
1
Factory Diagnostics Mode
Tachometer Verification Mode
1
8
8
(Status LED names may vary
between makes and models)
1
1
2
2
Dry Factory Diagnostics
Factory Cal Test Cycle
Clean Washer Cycle
8
8
8
4
2
2
1
Sensing Soak/
Final
Load
Wash
Rinse
Spin
Done
1
F
8
4
2
1
F2
2
3
4
Repeat…
STATUS LEDs
Frame Numbe
r
SENSING LOAD
SOAK
/W
AS
H
RINS
E
FINAL
SPI
N
DONE
Fault Code
E
8
4
2
1
E3
STATUS LEDs
SENSING LOAD
SOAK
/W
AS
H
RINS
E
FINAL
SPI
N
DONE
Error Cod
e