background image

9

Vacation, Storage and Moving Care

Install and store your washer where it will not freeze. Because 
some water may stay in the hoses, freezing can damage your 
washer. If storing or moving your washer during freezing weather, 
winterize it.

Non-use or vacation care

Operate your washer only when you are at home. If you will be on 
vacation or not using your washer for an extended period of time, 
you should:

Unplug washer or disconnect power.

Turn off the water supply to the washer. This helps avoid 
accidental flooding (due to a water pressure surge) while you 
are away.

To winterize washer

1. Shut off both water faucets.

2. Disconnect and drain water inlet hoses.

3. Put 1 quart (1 L) of R.V.-type antifreeze in the basket.

4. Run washer on a drain and spin setting (see “Drain and Spin”) 

for about 30 seconds to mix the antifreeze and water.

5. Unplug washer or disconnect power.

To use washer again

1. Flush water pipes and hoses.

2. Reconnect water inlet hoses.

3. Turn on both water faucets.

4. Plug in washer or reconnect power.

5. Run the washer through a complete cycle with 1 cup (250 mL) 

of detergent to clean out antifreeze.

TROUBLESHOOTING

First try the solutions suggested here and possibly avoid 
the cost of a service call...

Washer won’t fill, rinse or agitate

Check the following:
Is the power cord plugged into a grounded 3 prong outlet?

Is the indicator on the Cycle Control knob properly lined up 
with a cycle? Turn the Cycle Control knob to the right slightly 
and pull to start.

Are the water inlet valve screens clogged?

Are both the hot and cold water faucets turned on?

Is the water inlet hose kinked?

Does the water level seem too low, or does the washer 
appear to not fill completely?
The top of the agitator is much higher than the highest water 
level. This creates a perception that the washer is not filling 
completely. This is normal.

Washer stops

Check the following:
Is the power cord plugged into a grounded 3 prong outlet?

Is the indicator on the Cycle Control knob properly lined up 
with a cycle? Turn the Cycle Control knob to the right slightly 
and pull to start.

Are the water inlet valve screens clogged?

Are both the hot and cold water faucets turned on?

Is the water inlet hose kinked?

Is there power at the plug?
Check your electrical source or call an electrician.

Has a fuse blown or is the circuit breaker open?
If problem continues, call an electrician.

Are you using an extension cord?
Do not use an extension cord.

Is the washer in a normal pause in the Casual/Permanent 
Press (or Hand Washables) cycle?
The washer pauses for about 2 minutes in the Casual/
Permanent Press cycleAllow the cycle to continue.

The Hand Washables cycle (on some models) features 
periods of agitation and soak. 

Is the washer overloaded?
Wash smaller loads.

Washer won’t drain or spin

Is the drain hose clogged, or the end of the drain hose 
more than 72 in. (183 cm) above the floor?
See the Installation Instructions for proper installation of drain 
hose.

Is the lid open?
The lid must be closed during operation. 

Is there excessive sudsing?
Always measure detergent. Follow manufacturer’s directions. 
If you have very soft water, you might need to use less 
detergent. 

Is your voltage low?
Check your electrical source or call an electrician. Do not use 
an extension cord. 

Washer continues to fill or drain, or the cycle seems stuck

Is the top of drain hose lower than the water level in 
washer?
The top of the hose must be higher than the water level in the 
washer for proper operation. See the Installation Instructions.

Does the drain hose fit too tightly in the standpipe, or is it 
taped to the standpipe?
The drain hose should be loose yet fit securely. Do not seal 
the drain hose with tape. The hose needs an air gap. See the 
Installation Instructions.

Washer makes noise

Is the load balanced and the washer level?
The wash load should be balanced and not overloaded.

The washer must be level. The front feet should be properly 
installed and the nuts tightened. Reset the rear leveling legs 
(if needed). See the Installation Instructions.

Summary of Contents for 3955155A













Reviews: