background image

Page 1

®

ENGINEERING COMPANY INC.

Route 145, Winthrop Road,
Chester, Connecticut 06412
Phone: (860) 526-9504
Fax: (860) 526-4078
Internet: www.whelen.com
Sales e-mail: [email protected]
Canadian Sales e-mail: [email protected]
Customer Service e-mail: [email protected]

Installation/Operating Guide

Model MPC03

Multi-Purpose Controller

Safety First

This document provides all the necessary information to allow your Whelen product to be properly and safely installed.
Before beginning the installation and/or operation of your new product, the installation technician and operator must
read this manual completely. Important information is contained herein that could prevent serious injury or damage.

Proper installation of this product requires the installer to have a good understanding of automotive 
electronics, systems and procedures.

If mounting this product requires drilling holes, the installer MUST be sure that no vehicle components or 
other vital parts could be damaged by the drilling process. Check both sides of the mounting surface 
before drilling begins. Also de-burr any holes and remove any metal shards or remnants. Install grommets 
into all wire passage holes.

If this product is mounted with tape or Velcro™, clean the mounting surface with a 50/50 mix of 
superpolite alcohol and water and dry thoroughly.

Do not install this product or route any wires in the deployment area of your air bag. Equipment mounted 
or located in the air bag deployment area will damage or reduce the effectiveness of the air bag, or 
become a projectile that could cause serious personal injury or death. Refer to your vehicle owners 
manual for the air bag deployment area. The User/Installer assumes full responsibility to determine proper 
mounting location, based on providing ultimate safety to all passengers inside the vehicle.

For this product to operate at optimum efficiency, a good electrical connection to chassis ground must be 
made. The recommended procedure requires the product ground wire to be connected directly to the 
NEGATIVE (-) battery post.

If this product uses a remote device to activate or control this product, make sure that this control is 
located in an area that allows both the vehicle and the control to be operated safely in any driving 
condition.

Do not attempt to activate or control this device in a hazardous driving situation.

It is recommended that these instructions be stored in a safe place and referred to when performing 
maintenance and/or reinstallation of this product.

FAILURE TO FOLLOW THESE SAFETY PRECAUTIONS AND INSTRUCTIONS COULD RESULT IN DAMAGE 
TO THE PRODUCT OR VEHICLE AND/OR SERIOUS INJURY TO YOU AND YOUR PASSENGERS!

©2004 Whelen Engineering Company Inc.
Form No.13940B (020205)

Automotive:

 Serial Communication

Summary of Contents for MPC03











Reviews: