Wfly WFT09 Instruction Manual Download | Manualshive

Page: 55 / 106

background image

(5). TRIM OFFSET SETTING

This function is to adjust the servo trim at hovering state.
This function is used to automatically change the trim of a
helicopter, for example, when transitioned from hover to
flying at high speed. A clockwise-rotation rotor helicopter
tends to drift to the right at high speed, so an aileron offset
may be applied to offset the helicopter to the left.
The necessary elevator offset varies with model geometry,
so it must be determined by noting collective pitch changes
at high speed.
The rudder offset is affected by both revolution mixing and
trim lever movement while in the offset function.

Setting Method:

Use up/down button to select

Trim offset setting

, OK button

is to enter editing.

Steps:

1. Use direction buttons to select editing part.
2. Use +/- button to active or inhibit “Mix”.
3. Use +/- button to

s

et the control switch “CTRL”.

4. Use +/- button to set the control switch position “Pos“.
5. Use +/- button to set the channel, eg: ailerion, elevator, etc.
6. Use +/- button to set the mix rate “Rate”. Press OK button for
seconds can back default.
7. Press EXIT after setting.

WFT09

INSTRUCTION

48

HELICOPTER

«
...
53
54
55
56
57
...
»

Summary of Contents for WFT09











































































































Reviews:

No comments

Related manuals for WFT09

Brand: Lattice Semiconductor Pages: 30

Brand: WAFER Pages: 15

Brand: DAV TECH Pages: 10

Brand: CAME Pages: 98

Brand: CAME Pages: 16

Brand: CAME Pages: 8

Brand: Danfoss Pages: 32

PVG 16 PVH/Covers

Brand: Danfoss Pages: 112

Brand: Danfoss Pages: 44

PVG 16 PVH/Covers

Brand: Danfoss Pages: 144

Brand: Danfoss Pages: 2

Brand: Danfoss Pages: 64

Brand: Danfoss Pages: 8

VLT AutomationDrive FC 360

Brand: Danfoss Pages: 60

Brand: Danfoss Pages: 6

Brand: Danfoss Pages: 4

Brand: Danfoss Pages: 8

Brand: Danfoss Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands