Wfly WFT09 Instruction Manual Download | Manualshive

Page: 105 / 106

background image

(20). GYRO SENS SETTING

User can adjust the gyro sensitivity by transmitter,
AVCS gyro (GY) and normal gyro (STD).
Gyro sensitivity switch plug should plug in the fifth channel
of receiver. The auxiliary channel CH 5 won’t have any
function now. User can set sensitivity switch from switch A to F,
and also fly model (NORM, IDLE1,2,3).

Setting Method:

Use up/down button to select

GYRO sens setting

, OK button

is to enter editing.

Steps:

1. Use direction buttons to select editing part.
2. Use +/- button to set fly model at “MODE”.
3. Use +/- button to active or inhibit “Mix”. Press OK button
for seconds can back
default.
4. Use +/- button to set control switch at “CTRL”.
5. Use +/- button to set the switch position when the function
is active.
6. Use +/- button to set the “Rate”. Press OK button for seconds
can back default.
7. Press EXIT after setting.

97

WFT09

INSTRUCTION

AIRPLANE

«
...
103
104
105
106
»

Summary of Contents for WFT09











































































































Reviews:

No comments

Related manuals for WFT09

Brand: J4C Pages: 4

Brand: ABB Pages: 6

Brand: GE Pages: 425

Brand: Haier Pages: 58

Brand: Abicor Binzel Pages: 8

Brand: Vasco Pages: 32

Brand: Abra Pages: 16

Brand: SAI Pages: 16

Brand: Hable Pages: 3

Brand: nekos Pages: 8

Brand: nekos Pages: 8

Brand: Neles Pages: 12

Brand: RadioMaster Pages: 10

Brand: Xblue Networks Pages: 2

Brand: OEM Pages: 8

Brand: ABB Pages: 102

Brand: Dahua Pages: 137

Brand: Vizio Pages: 65

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands