Wfly ET08 Page 70 Instruction Manual Download

Page: 70 / 84

MODEL MENU \ AIRPLANE

GYRO

Interface path: HOME/MON. → [MODEL MENU] → [GYRO]

This function is used to adjust the gyroscope sensitivity. Set the sensitivity and mode of operation

(normal/AVCS) for each ﬂight condition or switch.

The control gyro sensitivity can be activated by "Fly

Condition" or by assigning switches, knobs, and so on.

3 modes can set the sensitivity separately

A switch, knob, etc. can be set to activate the sensitivity

value of the speciﬁed position of the switch.

Normal mode, (AVCS) locktail mode.

Set the associated tuning control switch, knob, etc. for

sensitivity adjustment

Gyro operation mode. Normal, AVCS100%

Can set the trim range value ±20%

Control switch current real-time position

Disable and enable the current Gyro conﬁguration group.

Each control switch may be provided gyro respectively,

three kinds of sensitivity can be provided.

1 When using the function, ﬁrst assign the function channel on the [Function] interface, and set the

"Switch” and “Trim” to [--] in [Function].

5 Type selecting. Select the sensitivity type of the corresponding work for the current "position".

2 Mode selecting. Optional "switch" or "Fly condition".

Function setting

4 Status selecting. Select whether the "Position" conﬁguration above is enabled or not.

6 Ratio adjustment. The options vary depending on the type option ("Normal" type, "Rate" range 0%-

100%; under "AVCS" type, "Rate" range is Normal[0~100%], AVCS[0~100%]) .

7 Trim the switch selection and trim the ratio setting. Sensitivity tuning switch, the default is [--]; the rate

value can be set to ±20%. Used for trimming the sensitivity.

The sensitivity required for diﬀerent ﬂight modes is diﬀerent, so switch the conditions (Position)

separately for sensitivity adjustment.

3 Position selecting. In each mode, there are 3 groups of positions to choose from, and the

corresponding sensitivity can be set separately. In the "switch" mode, you need to select the position
switch, the default is [--].

Summary of Contents for ET08





















































































Search results

Summary of Contents for ET08

Reviews:

Related manuals for ET08

Brands by name

Popular brands

Wfly ET08, Instruction Manual

Search results

Summary of Contents for ET08

Reviews:

Related manuals for ET08

Brands by name

Popular brands