background image

Wet Sounds REV 10 HD & REV 12 HD Owner’s Manual

Wet Sounds REV 10 HD & REV 12 HD Owner’s Manual

6

5

Step 1:  Attach Male Connector (6) from clamp base to Female Connector (7) 
Step 2:  Remove the plastic insert (3) from the clamp base (5).
Step 3:  

(Optional Step)

 If you use the RGB lighting function on a fixed clamp  

              application, drill a small hole in the seal point of the clamp base (5) to run 

              the RGB wires from the pod to the tower. Take care not do damage the 

              speaker wires when you drill through the seal.  Seal this point with silicon 

              after running the wires through. (This will require removing the four-pin 

              connector end from the RGB wires as this will not be used in this 

              application.)  

Step 4:  Push all wires and connectors into the pod’s center hole as you place the 

              clamp base (5) onto the speaker pod.

Step 5:  Attach two M8 x 30 bolts (4) through the clamp base (5) and tighten 

              them into the pod. Please make sure these are tight. We recommend 

              using threadlocker on these bolts.
Step 6:  Place the plastic insert (3)  back onto the clamp base (5).
Step 7:  Find a mounting location for the speaker and clamp, and mark the pipe 

              where the speaker wire will pass through.

Step 8:  Drill a small hole in the pipe where marked and deburr the hole, so 

              there are no sharp edges. We recommend installing a rubber grommet in 

              this hole to protect the wire. 
Step 9:  

(Recommended to be done by two people

) Butt connect the speaker wire 

              from the tower to the speaker wire from the clamp base (5). Red is positive, 

              and black is negative. If using the RGB Lighting Function, reference the RGB 

              wiring diagram for RGB color options.

Step 10:  Push wires into the center hole back into the tower and Attach the clamp 

               top (2) to the clamp base (5) using two M8 x 45 or M8 x 60 bolts (1) 

               depending on pipe diameter. Tighten the Allen bolts until there is no 

               movement. 

 

Installation Specifications

ADP TC3-F | Fixed Clamp (tube diameter 1 7/8” to 3”

)

(6) Male Connector

(7) Female Connector

(1) M8 x 45/60

(3) Plastic Insert

(2) Clamp Top

(5) Clamp Base

(4) M8 x 30

Summary of Contents for REV 10 HD










Reviews: