background image

Wet Sounds REV 10 HD & REV 12 HD Owner’s Manual

Thank you for choosing this Wet Sounds product!

Wet Sounds’ products embody the ultimate in high performance

standards. Utilizing state of the art acoustic engineering and 

three-dimensional computer aided design, our “Revolution Technology” 

represents the most advanced technologies available for tower speaker

systems. Revolution series speakers are specially engineered to withstand

rigorous environments while providing multiple fitment options from 

direct cast and fixed clamp mounts, to our patented stainless steel TC3 

Quick Disconnect Swivel clamp. 

The REV 10 HD and REV 12 HD Horn Loaded Compression Driver (HLCD) 

Tower Speakers have been optimized with audio clarity and high 

performance at their core. They both feature a Pro-Axial HLCD driver 

paired with an advanced polymer composite cone for audio clarity and 

durability. The thermoformed Santoprene™ rubber surround matched 

with the injection molded reinforced enclosure ensure optimal listening in 

any marine setting. The integrated RGB lighting rings and badge add the 

style for which Wet Sounds™ is synonymous. The REV 10 HD and REV 12 

HD both feature multiple grille options, several mounting choices, and are 

available in white or black to fit your style and taste.

Please take a moment to read the instruction manual before starting

your installation. This guide will explain the benefits of the technologies

developed by Wet Sounds™ and will help you understand the correct

installation methods and use of this product. If you have any questions

or concerns, please contact a certified Wet Sounds™ dealer. You may 

also contact Wet Sounds™ technical support by dialing 1-877-WET-SPKR 

(1-877-938-7757).

Congratulations!

Wet Sounds REV 10 HD & REV 12 HD Owner’s Manual

2

Table of Contents

Please take a moment to look over this instruction manual 

before enjoying the product.

Technology Specifications ..................................................... 3

Grilles, Clamps, Adapters ....................................................... 4

Install Guide ADP TC3-F (Fixed Clamp) ............................. 5-6 

Install Guide ADP TC3-S (Swivel Clamp) ............................ 7-8

Install Guide ADP TC3-SXM (Swivel Surface Mount)  .......9-10

Install Guide ADP REV HD X (X Mount) ...........................11-12

RGB Wiring ............................................................................

...13

Limited Warranty .................................................................

...14

Summary of Contents for REV 10 HD










Reviews: