Western LOW-PRO 300W Mechanic'S Manual Download Page 79

Page: 79 / 106

Lit. No. 72131, Rev. 00

July 15, 2018

Excerpts taken from Hopper Spreader Pre-Wet Kit (On/Off System) Owner's Manual/Installation Instructions/Parts List (Lit. No. 70429, Rev. 03).

ACCESSORIES – PRE-WET KIT: ON/OFF CONTROL (STEEL & POLY HOPPER SPREADERS)

TROUBLESHOOTING GUIDE

Problem

Possible Cause

Suggested Solution

Pump is not operating.

1. Loose electrical connection.

1. Check all electrical connections for corrosion.

2. Blown fuse.

2. Replace the fuse.

3. Pump seized.

3. Replace the pump.

Control shut down.

1. Loose electrical connection.

1. Check all electrical connections for corrosion.

2. Electrical short.

2. Check for bare or burned wires.

3. Control failure.

3. Replace the control.

4. Blown fuse.

4. Replace the fuse.

Material being spread is not wet.

1. Pre-wet system is not running.

1. See "Pump is not working" in Troubleshooting

section of Owner's Manual/Installation Instructions/
Parts List.

2. Spray hose is misaligned.

2. See "Aligning the Spray Hose" in the Owner's

Manual/Installation Instructions/Parts List.

3. Flow rate is set too low.

3. See "Adjusting the Flow" in the Owner's Manual/

Installation Instructions/Parts List.

Spray is uneven.

1. Spray hose is clogged.

1. Clean spray hose with fresh water.

2. Spray hose is damaged.

2. Replace the spray hose.

Pump is leaking.

1. O-ring

ttings are loose.

1. Verify that O-ring

ttings are fully installed.

2. O-rings are damaged or worn.

2. Replace the O-rings.

3. Pump housing is damaged.

3. Replace the pump.

Summary of Contents for LOW-PRO 300W











































































































Search results

Summary of Contents for LOW-PRO 300W

Reviews:

Related manuals for LOW-PRO 300W

Brands by name

Popular brands

Western LOW-PRO 300W, Mechanic'S Manual

Search results

Summary of Contents for LOW-PRO 300W

Reviews:

Related manuals for LOW-PRO 300W

Brands by name

Popular brands