background image

Warning! Shock Hazard! No User Serviceable Parts.

Do not attempt service of this control system.  Contact your dealer or service organization for assistance.  Follow all owner’s manual power 
connection instructions.  Installation must be performed by a licensed electrician and all grounding connections must be properly installed.

Message

No message on display. 
Power has been cut off to the spa.

Temperature unknown.

“Overheat” - The spa has shut down.  One of the 
sensors has detected 118°F/48°C at the heater.

“Overheat” - The spa has shut down.  One of 
the sensors has detected that the spa water is 
110°F/43°C.

“Ice” - Potential freeze condition detected.

Spa is shut down.  The sensor that is plugged into 
the Sensor “A” jack is not working.

Spa is shut down.  The sensor that is plugged into 
the Sensor “B” jack is not working.

Sensors are out of balance.  If alternating with 
spa temperature, it may just be a temporary 
condition.  If flashing by itself, spa is shut down.

A significant difference between temperature 
sensors has been detected.  This could indicate a 
flow problem.

Persistent low flow problems.  (Displays on the 
fifth occurrence of “

” message within 24 hours.)   

Heater is shut down, but other spa functions 
continue to run normally.

Possible inadequate water, poor flow, or air 
bubbles in detected in the heater.  Spa is shut 
down for 15 minutes.

Inadequate water detected in heater.  (Displays on 
third occurrence of “

” message.)  Spa is 

shut down.

The control panel will be disabled until power returns.  Spa 
settings will be preserved until next power up.

After the pump has been running for 2 minutes, the 
temperature will be displayed.

DO NOT ENTER THE WATER.  Remove the spa cover 
and allow water to cool.  Once the heater has cooled, reset by 
pushing any button.  If spa does not reset, shut off the power to 
the spa and call your dealer or service organization.

DO NOT ENTER THE WATER.  Remove the spa cover 
and allow water to cool.  At 107°F/42°C, the spa should 
automatically reset.  If spa does not reset, shut off the power to 
the spa and call your dealer or service organization.

No action required.  The pump and blower will automatically 
activate regardless of spa status.

If the problem persists, contact your dealer or service 
organization.  (May appear temporarily in an overheat situation 
and disappear when the heater cools.)

If the problem persists, contact your dealer or service 
organization.  (May appear temporarily in an overheat situation 
and disappear when the heater cools.)

If the problem persists, contact your dealer or service 
organization.

Check water level in spa. Refill if necessary.  If the water level 
is okay, make sure the pumps have been primed.  If problem 
persists, contact your dealer or service organization.

Follow action required for “

” message.  Heating capability of 

the spa will not reset automatically; you may press any button 
to reset.

Check water level in spa.  Refill if necessary.  If water level is 
okay, make sure the pumps have been primed.  Press any button 
to reset, or this message will automatically reset within 
15 minutes.  If problem persists, contact your dealer or service 
organization. 

Follow action required for “

” message.  Spa will not 

automatically reset.  Press any button to reset.

Meaning

Action Required

Diagnostic Messages

Summary of Contents for TRIGLAV




























Reviews: