Well 8820IP User Manual Download

Page: 54 / 54

8820IP Phone User Manual_ SIP (V1.44)

PalmTool. This operation aims at testing.

X-1: Connect to FTP Server to get the file of updating program and

update program Flash. This operation aims at updating program.

X-2: Connect to FTP Server to get the file of updating dial rules and

update program Flash. This operation aims at updating dial rule.

Note

When you use ftp 0 and ftp 1 commands, if the file get from FTP server is too

large or the net speed is too slow, then the process will not be seen in telnet

window. Please be patient. Using ftp command in telnet to get file spends almost

same minutes as getting file using phone. So if nothing is displayed after too long

time, it means that ftp is fail.

Note

All the Telnet commands of PA168X IP phone should be written in low case and

the password is case sensitive.

Summary of Contents for 8820IP























































Search results

Summary of Contents for 8820IP

Reviews:

Related manuals for 8820IP

Brands by name

Popular brands

Well 8820IP, User Manual

Search results

Summary of Contents for 8820IP

Reviews:

Related manuals for 8820IP

Brands by name

Popular brands