8.0 Trobuleshooting
Refer to the following table if you are experiencing trouble with your camera.
Contact an authorized technician if the table does not provide you with a solution to the trouble
Day & Night 10X Zoom Camera
36
Problems
Troubleshooting
No display
Dim display
Dark display
The camera is not functioning properly
and its surface is hot
Motion Detection feature is not active.
Uneven colors Flickering
Can't select LL mode
LL is not function properly.
l
Check the power cable and the wiring between the camera and the monitor.
l
Ensure proper video cable connection (Video Out Jack).
l
The lens could be dirty. Clean with a soft, clean piece of cloth.
l
Adjust monitor settings.
l
Adjust camera position if exposed to a strong light source.
l
Adjust the monitor's contrast level.
l
Set the intermediate device, if in use, to 75
Ω
/ Hi-z (
refer to p.11
).
l
Check the power source for compliance with specifications.
l
Ensure that the feature is set to ON.
l
Adjust and configure WHITE BAL.
l
The camera may be facing the sun or a fluorescent light.
Adjust the position of the camera.
l
The camera may be connected to a DC power source.
Connect to an AC power source.
l
Check external SYNC signal frequency (should be 60Hz for NTSC, 50Hz for PAL).
SPECIAL SETUP
USER PRESET
PRIVACY
DAY/NIGHT
SYNC
COMM ADJ
IMAGE ADJ
END
OFF
OFF
COLOR
INIT
c
IMAGE ADJ:
Includes image quality or special function factors.
q
FREEZE:
Use this feature to freeze capture an image
.
q
H-REV:
Use this feature to horizontally inverse the screen.
q
V-REV:
Use this feature to vertically inverse the screen.
q
SHARPNESS:
Increasing this value sharpens object edges.
Too high of a setting, however, produces noise
and may obscure the image.
q
COLOR AGAIN:
Adjusting this value affects the chroma level only;
the burst level is unaffected.
c
END:
evert back to the USER PRESET menu.
7.4.8 RESET
To reset your camera to factory default condition.
7.4.9 EXIT
To finish setup menu.
Day & Night 10X Zoom Camera
35
Note
q
For NTSC models, the line-lock mode can be used if the external SYNC signal frequency is at 60Hz.
q
For PAL models, the line-lock mode can be used if the external SYNC signal frequency is at 50Hz.
SPECIAL SETUP
USER PRESET
PRIVACY
DAY/NIGHT
SYNC
COMM ADJ
OFF
OFF
COLOR
INIT
SPECIAL SETUP
USER PRESET
PRIVACY
DAY/NIGHT
SYNC
COMM ADJ
IMAGE ADJ
END
OFF
OFF
COLOR
INIT
c
SYNC:
Two synchronization modes are available
INTERNAL and EXTERNAL LINE-LOCK.
In LINE-LOCK mode, it synchronizes the camera's video out
signal to the external SYNC signal.
q
INT:
Internal synchronization.
q
LL:
External line-lock synchronization
If you choose 'LL', you can adjust the desired phase.Press the SET button.
You can adjust the desired phase from 0 to 359.
c
COMM ADJ:
Use this feature to select communication protocol.
Position the indicator over 'COMMUNICATION' using
the TELE(UP) or WIDE(DOWN) button.
q
CAM ID : Assign ID number to the camera.
It is restricted available to set ID from 1 to 255.
q
DISP CAM ID: Displays camera ID on top left corner of the screen.
q
BAUD RATE: Configure baud rate from 9600, 19200, 38400, 57600bps.
q
UART MODE: Configure parity bit to NONE, EVEN, or ODD.
Data bit is set to 8bit, and stop bit to 1bit.
Set the UART MODE to EVEN if using the Remote Controller.
q
RET PKT : Used to transfer a packet.
q
END
Day & Night 10X Zoom Camera
34
