Weil-McLain AHE Series Page 11 Manual Download | Manualshive

Page: 11 / 48

background image

Part number 550-141-887/0800

11

AHE

Series 4 Direct Vent Wall-Mounted Boilers

— Boiler Manual

2b

Venting — side venting installation

con’t

Prepare mounting panel

continued

Inside

15. Insert wall sleeve (see Figure 32, item 1, page 44) into outside wall

plate assembly.

16. Measure tube lengths. See Figure 6 on page 10.
17. Cut tube lengths. Top tube will be longer than bottom tube.
18. Final location of boiler will be determined by proper slope to vent/air

intake tubes. Vent must slope downward from boiler ¼" per foot of
vent run to prevent outside moisture from draining into boiler. See
Figure 7, right.

19. Check vent tube slope:

a.

Place top tube in top opening of outside wall plate (See Figure 32,
items 1 and 2 on page 44).

b.

Measure from floor to bottom of tube at side wall.

c.

Measure from floor to bottom of tube at plenum box end of tube.

d.

Distance should differ ¼" per foot of vent run (length of top tube).
Adjust large template to locate bottom-of-tube mark at correct
slope.

e.

Remove tube.

20. Drill stud holes in template. Remove template.
21. Apply generous bead of silicone sealant around insertion end of tubes,

1" from end of tube.

22. Place tubes in openings. See Figure 8.
23. Place inside wall plate (see Figure 32, page 44, item 3) over tubes, against

wall.

24. Slide mounting panel (Figure 32, page 44, item 5) over tubes. Tubes

will extend into plenum box openings.

25. Securing mounting panel to studs with (2)

5

/

16

" x 2¼" lag screws

provided. Use toggle bolts on plywood.

26. Place a continuous amount of silicone sealant around junctions of tubes

and plenum boxes. Also place sealant in four (4) screw holes where
blank cover plate was attached to the bottom (air intake) plenum box.
Smooth sealant to provide complete seal. See Figure 8.

27. Fasten inside wall plate, using (4) #10 x ½" screws provided.

Reassembly

When vent/air intake system is disconnected for any reason, reassemble
and reseal per this manual section.

Silicone sealant must be used where indicated. Vent/air
intake system must be sealed gas-tight to prevent
possibility of flue gas spillage and carbon monoxide
emissions, resulting in severe personal injury, death or
substantial property damage.

Figure 8

Side venting installation

Fasteners

Screws

88709

Silicone
sealant

Figure 7

Vent slope

88708

¼" slope down
per linear foot

Silicone sealant

«
...
9
10
11
12
13
...
»

Summary of Contents for AHE Series

















































Reviews:

No comments

Related manuals for AHE Series

Semia Condens F24 E

Brand: Saunier Duval Pages: 52

LOGIC SYSTEM S15IE

Brand: Ideal Heating Pages: 80

Brand: Garland Pages: 2

Ciao S 20 C.S.I.

Brand: Beretta Pages: 31

Brand: A.O. Smith Pages: 48

Brand: OSO HOTWATER Pages: 64

Brand: Saturn Pages: 17

Brand: Watts Pages: 25

Brand: Ariston Pages: 10

Initia SUPER 1.24 FF

Brand: Chappee Pages: 50

Brand: Raypak Pages: 8

Brand: HTP Pages: 66

Brand: AFRISO Pages: 2

Brand: Legacy Stoves Pages: 51

Brand: Potterton Pages: 12

Brand: Potterton Pages: 40

Brand: Ideal Heating Pages: 29

Brand: Viessmann Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands