background image

 

 

II 3G

 ATEX Information 

1.  Certification number DEMKO 11 ATEX1106692x 
2.  Ambient range (-40°C 

 Tamb 

 75°C) 

3.  Certification string (Ex nC nL IIC T4) 
4.  Standards covered ( EN60079-0:2006, EN60079-15:2005) 
5.  The conditions of safe usage: 

y

  The Ethernet Communication Devices are to be mounted in an 

IP54 enclosure and used in an area of not more than pollution 
degree 2 as defined by IEC60664-1. A 4mm2 conductor must 
be used when a connection to the external grounding screw is 
used. Conductors suitable for use in an ambient temperature of 
93°C must be used for the Power Supply Terminal. 

y

  Provisions shall be made, either in external to the apparatus, to 

prevent the rated voltage being exceeded by the transient 
disturbances of more than 40%. 

Wiring Requirements 

WARNING 

 

Do not disconnect modules or wires unless power 
has been switched off or the area is known to be 
non hazardous. 
The devices may only be connected to the supply 
voltage shown on the type plate. 
The devices are designed for operation with a 
safety extra-low voltage. Thus, they may only be 
connected to the supply voltage connections and to
the signal contact with the safety extra-low 
voltages (SELV) in compliance with IEC950/ 
EN60950/ VDE0805.

 

 

WARNING 

 

Substitution of components may impair suitability 
for Class I, Division 2 and Zone 2. 
These devices must be supplied by a SELV source 
as defined in the Low Voltage Directive 73/23/EEC 
and 93/68/EEC.

 

 

 

- 6 -

Summary of Contents for IE-MC-VL















Reviews: