background image

 

- 14 -

Ambient Relative Humidity   5 to 90% (non-condensing) 

Regulatory Approvals 

 

Safety 

UL60950, UL 508, CSA C22.2 No. 60950, 
EN60950 

Hazardous Location 

UL/cUL Class I, Division 2, Groups A, B, C 
and D 
ATEX Class I, Zone 2, EEx nC IIC   

EMI 

FCC Part 15, CISPR (EN55022) class A 

EMS 

EN61000-4-2 (ESD), level 3 
EN61000-4-3 (RS), level 3 
EN61000-4-4 (EFT), level 3 
EN61000-4-5 (Surge), level 2 
EN61000-4-2 (CS), level 3 

Shock IEC 

60068-2-27 

Free Fall 

IEC 60068-2-32 

Vibration IEC 

60068-2-6 

 
WARRANTY 

 
5 years 

 

Weidmüller gives a 5 year warranty on this product in accordance with 
the warranty terms as described in the general conditions of sale of 
the Weidmüller company which has sold the products to you. 
Weidmüller warrants to you that such products the defects of which 
have already existed at the time when the risk passed will be repaired 
by Weidmüller free of charge or that Weidmüller will provide a new, 
functionally equivalent product to replace the defective one. Safe 
where expressly described otherwise in writing in this 
catalogue/product description, Weidmüller gives no warranty or 
guarantee as to the interoperability in specific systems or as to the 
fitness for any particular purpose. To the extent permitted by law, any 
claims for damages and reimbursement of expenses, based on 
whatever legal reason, including contract or tort, shall be excluded. 
Where not expressly stated otherwise in this warranty, the general 
conditions of purchase and the expressive liability commitments 
therein of the respective Weidmüller company which has sold the 
products to you shall be applicable.

 

 
 
 
 

Contact Information 

 

Weidmüller Interface GmbH & Co. KG 

Postfach 3030 

32760 Detmold 

Klingenbergstraße 16 

32758 Detmold 

Germany 

 

Phone +49 (0) 5231 14-0 

Fax +49 (0) 5231 14-2083 

E-Mail [email protected] 

Internet www.weidmueller.com 

Summary of Contents for IE-MC-VL















Reviews: