22
49
42
32
35
24
51
36
ATTACHING THE SEAT FRAME
To attach the Seat Frame (36) to the Front Upright
(42), slide one of the three slots in the bracket on the
Seat Frame onto the pin on the Upright. Note: The
Seat Frame can be adjusted to three different
heights using the three slots. Secure the Seat
Frame to the Upright with the M10 x 80mm Carriage
Bolt (99) and the Seat Knob (49).
For some exercises, the Seat Frame (36) must be
removed. First, make sure that the chain is not attached
to the leg lever. Next, remove the Seat Knob (49) and
the M10 x 80mm Carriage Bolt (99) from the Seat
Frame. Lift the Seat Frame off the Front Upright (42).
36
99
Pin
Slot
ATTACHING THE CURL PAD
To attach the Curl Pad (24) to the weight system, the
seat frame must be attached to the front upright (see
ATTACHING THE SEAT FRAME above). Remove the
38mm Square Inner Cap (32) from the Seat Frame
(36). Insert the Curl Post (35) into the Seat Frame and
secure it with the Curl Knob (51).
Always remove the Curl Pad (24) when it is not in use,
and replace the 38mm Square Inner Cap (32).
To use the Curl Bar (67) to do curl exercises, attach
one end of a Chain (52) to the Curl Bar with a Cable
Clip (53). Attach the other end of the Chain to the indi-
cated Eyebolt (109) on the Leg Lever (29) with a
Cable Clip.
69
53
52
29
ATTACHING THE LEG LEVER TO THE LOW
CABLE
To use the Leg Lever (29), the seat frame must be
attached to the front upright (see ATTACHING THE
SEATFRAME above).
Attach one end of the Chain (52) to the end of the
Low Cable (69) with a Cable Clip (53). Attach the
other end of the Chain to the bracket on the back of
the Leg Lever (29) with another Cable Clip.
7
3.
Attach the Support Upright (88) to the Stabiliser
(5) with the indicated two M10 x 55mm Carriage
Bolts (1) and two M10 Nylon Locknuts (21). Do
not tighten the M10 Nylon Locknuts yet. Make
sure the Support Upright leans toward the
center of the Stabiliser.
Attach the Carriage Upright (84) to the Stabiliser
(5) with the indicated two M10 x 55mm Carriage
Bolts (1) and two M10 Nylon Locknuts (21). Do
not tighten the M10 Nylon Locknuts yet.
4.
Turn the Carriage Knob (73) counter clockwise
and pull it out as far as it will go. Slide the
Carriage (89) onto the Carriage Upright (84) and
engage the Knob into one of the adjustment holes
in the Upright. Fully tighten the Knob. Make sure
the Carriage is oriented as shown. Be careful
not to scratch the decals on the Upright as
you slide the Carriage over them.
Attach the Swivel Bracket (81) to the Carriage
(89) with an M10 x 158mm Bolt (108) and an M10
Nylon Locknut (21). Do not overtighten the M10
Locknuts; the Swivel Bracket must be able to
pivot easily.
Press two 60mm Square Inner Caps (101) into
the top of the Carriage Upright (84) and the
Support Upright (88).
3
84
88
21
21
21
21
1
5
1
81
4
21
89
108
84
Adjustment
Hole
88
73
101
101
67
53
52
109
29
53
