12
19. Wrap the High Cable (11) around a 90mm Pulley
(15). Attach the Pulley to the Pulley Bracket (20)
with an M10 x 47mm Bolt (103) and an M10
Nylon Locknut (21).
Attach the Pulley Bracket (20) to the Top Frame
(55) with an M10 Washer (9) and an M10 Nylon
Locknut (21). Do not overtighten the Locknut.
18. Wrap the High Cable (11) around a “V”-pulley (6).
Attach the “V”-pulley and a Long Cable Trap (50)
to the Left Butterfly Arm (47) with an M10 x 60mm
Bolt (7) and an M10 Nylon Locknut (21). Make
sure the Cable Trap is oriented to hold the
Cable in the groove of the “V”-pulley.
Repeat this step with the Right Butterfly Arm
(48).
18
19
7
6
50
21
11
47
48
20
103
21
21
15
11
55
9
17
37. Attach the Low Cable (69) to the Front Upright
(42) with an M8 x 80mm Shoulder Bolt (95), two
M8 Washer (70), and an M8 Nylon Locknut (3).
39. Wrap the Carriage Cable (83) around a 90mm
Pulley (15) and route it through the hole in the
Carriage Upright (84). Attach the Pulley and a
pair of Pulley Covers (40) to the bracket on the
Carriage Upright with an M10 x 52mm Bolt (12)
and an M10 Nylon Locknut (21). Make sure the
large tabs on the Pulley Covers are on the
side shown.
40. Wrap the Carriage Cable (83) up around a 90mm
Pulley (15). Attach the Pulley and a pair of Pulley
Covers (40) inside the indicated bracket on the
Stabiliser (5) with an M10 x 105mm Bolt (106).
Push the Bolt only through the first bracket.
Make sure the large tabs on the Pulley Covers
are on the side shown.
Hold a 12.5mm Spacer (82) between the two
brackets on the Stabiliser (5). Push the M10 x
105mm Bolt (106) through the Spacer, but not
into the next bracket.
38. Attach a 90mm Pulley (15) to the top hole in the
Swivel Bracket (81) with an M10 x 45mm Bolt
(100) and an M10 Nylon Locknut (21).
Locate the Carriage Cable (83), which has a ball
on one end and a eyelet on the other. Wrap the
Cable around a 90mm Pulley (15). Attach the
Pulley to the bottom hole in the Swivel Bracket
(81) with an M10 x 45mm Bolt (100) and an M10
Nylon Locknut (21).
37
38
39
40
42
3
69
95
70
70
100
21
81
15
83
12
15
83
84
21
40
Large
Tab
40
Large
Tab
40
15
83
82
106
5
40
20. Wrap the High Cable (11) under a 90mm Pulley
(15). Attach the Pulley and a pair of Pulley
Covers (40) to the top hole in the Large “U”-
bracket (90) with an M10 x 52mm Bolt (12) and
an M10 Nylon Locknut (21). Make sure the small
tabs on the Pulley Covers are on top.
20
90
12
21
15
11
40
40
Small
Tab
21. Attach the High Cable (11) to the bracket on the
Front Upright (42) with an M10 x 22mm Bolt (98),
an M10 Washer (9), and an M10 Nylon Locknut
(21).
42
98
21
11
21
9
