Wegener iPump 562 User Manual Download Page 33

Page: 33 / 33

www.wegener.com

800092-02 Rev. C

Warranty

The following warranty applies to all

WEGENER

products:

All

WEGENER

products are warranted against defective materials and workmanship for a period of one

year after shipment to customer .

Wegener Communications

' obligation under this warranty is limited

to rep airing or , at W egener Communications' option, replacing p

arts, subassemblies, or entire

assemblies.

W egener Communications

shall not be liable for any special, indirect, or consequential

damages. This warranty does not cover p

arts or equipment, which have been subject to misuse,

negligence, or accident by the customer during use. All shipping cost

s for warranty rep airs shall be

prepaid by the customer. There are no other warranties, express or implied, except as st ated herein.

Technical Support

In the event that the unit fails to perform as described, contact

Wegener Communications

Customer Service at:

Phone:

(770) 814-4057

Fax:

(770) 232-0621

E-mail:

[email protected]

Corporate Office:

Service Department:

WEGENER WEGENER

11350 Technology Circle

Customer Service

John's Creek

11350 Technology Circle

Duluth, GA 30097

Summary of Contents for iPump 562


































Search results

Summary of Contents for iPump 562

Reviews:

Related manuals for iPump 562

Brands by name

Popular brands

Wegener iPump 562, User Manual

Search results

Summary of Contents for iPump 562

Reviews:

Related manuals for iPump 562

Brands by name

Popular brands