WEG SSW900 Series User Manual Download Page 23 | Manualshive

Page: 23 / 65

WEG SSW900 Series User Manual Download Page 23

OPERATION IN THE ETHERNET/IP NETWORK

Table 6.1:

Example of conﬁguration of the writing words.

Conﬁguration Parameter

Mapped Parameter

Net Id

Input Area Value

C8.1.1.30 Data Read Word #26

S5.1.1

680

0063h

C8.1.1.31 Data Read Word #27

S1.2.4

4

088Ah

C8.1.1.32 Data Read Word #28

S1.1.4

24

0017h (S1.1.4 low word)

C8.1.1.33 Data Read Word #29

S1.1.4

24

0000h (S1.1.4 high word)

C8.1.1.34 Data Read Word #30

S1.5.4

8

000Eh

✓

NOTE!

Mapping of invalid parameters or not available will return zero value.
The data is transmitted as an integer value, without the indication of the decimal places.
To obtain the network address (Net Id) of the parameters, refer to Appendix A.

6.1.2

Output Words

The SSW900 soft-starter has a writing area with 20 16-bit words available for cyclic data exchange of communication
networks. The data available in the write area (Output) is received from the network master. This area is shared
between the two Slots.

To map an object in the writing area, follow the steps below.

1. Conﬁgure parameter C8.1.2.1 (Slot 1) or C8.1.2.3 (Slot 2). Those parameters indicate which of the writing

words starts the output area for the speciﬁc Slot.

2. Conﬁgure on parameter C8.1.2.2 (Slot 1) or C8.1.2.4 (Slot 2) the quantity of reading words which must be

transmitted via network.

3. Parameters C8.1.2.6 to C8.1.2.25 enable to conﬁgure the data that must be provided on the writing words.

Those parameters must contain the network address (Net Id) of the data that must be transmitted on the
respective writing words. The Net Id list is available on the table A.2. Consider the size of each parameter
mentioned in list when programming each word.

Exemplo

The example below presents a conﬁguration for Slot 1. Considering the following parameters to be mapped:

S5.2.5 Command Word Slot1.
S5.3.1 Value for Outputs DO Value.
S5.3.2.1 Value for AO AO in 10 bits.

Searching parameter information on the table A.2:

Mapped Parameter

Net Id

Size

Qty Mapped Words

Example Value

S5.2.5 Command Word Slot1

685

16bit

1

19 = 0013h

S5.3.1 Value for Outputs DO Value

695

16bit

1

7 = 0007h

S5.3.2.1 Value for AO AO in 10 bits

696

16bit

1

1023 = 03FFh

Therefore, the conﬁguration must be performed as shown below:

1. C8.1.2.1 Data Write Slot 1 1st Word = 1

→

ﬁrst word transmitted via network is the word #1.

2. C8.1.2.2 Data Write Slot 1 Quantity = 3

→

sum of column “Qty mapped words”.

SSW900 | 23

«
...
21
22
23
24
25
...
»

Summary of Contents for SSW900 Series


































































Reviews:

No comments