manualshive.com logo in svg

WEG SSW900 Series, User Manual, Page: 8 / 65

Share
Download
WEG SSW900 Series User Manual Download Page 8

INTERFACE DESCRIPTION

2 INTERFACE DESCRIPTION

The SSW900 soft-starter has two Slots for accessories (Figura 2.1). Parameters S3.5.1 and S3.5.2 present which
accessory was recognized by Slot.

The accessories can be connected to any Slot, but only one type of each communication accessory is allowed. The
Anybus-CC communication accessories (regardless of the protocol implanted) are identified on these parameters as

Anybus-CC

.

Read the user’s manual of the SSW900 soft-starter before installing or using this accessory.

Slot 1

Slot 2

Figure 2.1:

Slots for accessories

✓

NOTE!

Only one Anybus-CC communication accessory can be connected to the SSW900 soft-starter, even
if they are different protocols.

2.1 ANYBUS ETHERNET/IP ACCESSORY

SSW900-CETH-IP-N:

Supplied items:

–

Installation guide.

–

Anybus EtherNet/IP communication module.

–

”torx” screw driver for fixing the module.

–

It allows the programming of the drive via network configuration
software.

2.2 CONNECTORS

The accessory for EtherNet/IP communication has two RJ45 connectors for network connection. The connector pin
out follows the Fast Ethernet 100BASE-TX standard, using two pairs of cables for data transmission and reception.

SSW900 | 8

Summary of Contents for SSW900 Series


































































Reviews:

No comments