6
Please Do Not Return This Product To The Store.
Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer, refer to your
local yellow pages/business listings or go to the
Find a Dealer
section online at
www.wayne-dalton.com
Tools Needed:
TRack TyPe
ToRSioN
12” R
14”
14”R
17”
3.5 LhR REAR
7”
3.5 LhR FRONT
10”
heaDRoom RequiRemeNTS
Preparing the opening
P2
WEAThER SEAL
hEADROOM
BACKROOM
DOOR
WIDTh
DOOR hEIGhT
LEVEL hEADER
PLUMB jAMBS
hEADER BOARD
2” x 6” LUMBER
RECOMMENDED
SUITABLE MOUNTING
SURFACE 2” x 6”
LUMBER MINIMUM
hEADER
jAMB
jAMB
jAMB 1/8” TO 1/4”
WEAThER
SEAL
FAILURE TO SECURELY ATTACh A SUITABLE
MOUNTING PAD TO STRUCTURALLY SOUND
FRAMING COULD CAUSE SPRINGS TO
VIOLENTLY PULL MOUNTING PAD FROM WALL,
RESULTING IN SEVERE OR FATAL INjURY.
If you just removed your existing door or you are installing a new door,
complete all steps in PREPARING ThE OPENING.
To ensure secure mounting of track brackets, side and center bearing
brackets, or steel angles to new or retro-fit construction, it is recommended
to follow the procedures outlined in DASMA Technical Data Sheets #156,
#161 and #164 at www.dasma.com.
The inside perimeter of your garage door opening should be framed with
wood jamb and header material. The jambs and header must be securely
fastened to sound framing members. It is recommended that 2” x 6” lumber
be used. The jambs must be plumb and the header level. The jambs should
extend a minimum of 14” (356 mm) above the top of the opening for Torsion
spring applications. For low headroom applications, the jambs should extend
to the ceiling height. Minimum side clearance required, from the opening to
the wall, is 3-1/2” (89 mm).
imPoRTaNT:
CLOSELY INSPECT ExISTING jAMBS, hEADER AND MOUNTING
SURFACE. ANY WOOD FOUND NOT TO BE SOUND, MUST BE REPLACED.
For Torsion spring applications, a suitable mounting surface must be firmly
attached to the wall, above the header at the center of the opening. The
mounting surface must be 2” x 6” lumber minimum (Select southern yellow
pine lumber. Do not use lumber marked as spruce-pine-fur or SPF). The
mounting surface must be securely attached to the wall with four (4) 3/8”
anchors for masonry constructions or four (4) 5/16” x 4” lag screws for wood
construction.
NoTe:
Drill a 3/16” pilot hole in the mounting surface to avoid splitting the
lumber. Do not attach the mounting surface with nails.
weather Seal (may Not be included):
Cut or trim the weather seal (if necessary) to the header and jambs.
For fully adjustable track:
Align the header seal 1/8” to 1/4” inside the
header and temporarily secure it to the header with equally spaced nails.
Next, fit the jamb seals up tight against the header seal and 1/8” to 1/4”
inside the jamb. Temporarily secure the jamb seals with equally space nails
approximately 12” to 18” apart. This will keep the bottom section from
falling out of the opening during installation.
NoTe:
Do not permanently attach weather seal to the jamb at this time.
heaDRoom RequiRemeNT:
headroom is defined as the space needed
above the top of the door for tracks, springs, etc. to allow the door to open
properly. If the door is to be motor operated, 3” (76 mm) of additional
headroom is required.
backRoom RequiRemeNT:
Backroom is defined as the distance needed
from the opening back into the garage to allow the door to open fully.
waRNiNg
DooR
heighT
TRack
TyPe
backRoom
maNual liFT
backRoom
RequiRemeNTS
(moToR oPeRaTeD)
6’0” - 8’0”
12” R
Opening height
+ 18”
Opening 66”
6’0” - 8’0”
14”R
Opening height
+ 18”
Opening 66”
6’0” - 8’0”
3-1/2”
LhR
REAR
Opening height
+ 30”
Opening 66”
6’0” - 8’0”
3-1/2”
LhR
FRONT
Opening height
+ 30”
Opening 66”
backRoom RequiRemeNTS
Tape Measure
