Wavecom WMO1-G900 User Manual Download Page 55

Page: 55 / 67

Wavecom GSM Modem

This confidential document is the property of WAVECOM and may not be copied or circulated without permission

Switching equipment congestion

Access information discarded

requested circuit/channel not available

Resources unavailable, unspecified

Quality of service unavailable

Requested facility not subscribed

Incoming calls barred with in the CUG

Bearer capability not authorized

Bearer capability not presently available

Service or option not available, unspecified

Bearer service not implemented

ACM equal to or greater than ACMmax

Requested facility not implemented

Only restricted digital information bearer capability is
available

Service or option not implemented, unspecified

Invalid transaction identifier value

User not member of CUG

Incompatible destination

Invalid transit network selection

Semantically incorrect message

Invalid mandatory information

Summary of Contents for WMO1-G900




































































Search results

Summary of Contents for WMO1-G900

Reviews:

Related manuals for WMO1-G900

Brands by name

Popular brands

Wavecom WMO1-G900, User Manual

Search results

Summary of Contents for WMO1-G900

Reviews:

Related manuals for WMO1-G900

Brands by name

Popular brands