Wavecom WMO1-G900 User Manual Download Page 21

Page: 21 / 67

Wavecom GSM Modem

This confidential document is the property of WAVECOM and may not be copied or circulated without permission

4.4. Manufacturer identification +CGMI

This command gives the manufacturer identification.

Application to GSM

AT+CGMI

get manufacturer identification

GSM to application

WELCOME
OK

command valid (« WELCOME » is not a
manufacturer identification !)

4.5. Capabilities list +GCAP

This command gives the complete capabilities list.

Application to GSM

AT+GCAP

get capabilities list

GSM to application

+CGSM
OK

supports GSM commands

4.6. Phone activity status +CPAS

This command returns the activity status of the mobile.

Application to GSM

AT+CPAS

Current activity status

GSM to application

+CPAS: "x"
OK

"x" as defined in the GSM TS 07 07

4.7. Power off +CPOF

This command stops the GSM software stack and then the hardware

layer.

Application to GSM

AT+CPOF

GSM to application

command valid

Summary of Contents for WMO1-G900




































































Search results

Summary of Contents for WMO1-G900

Reviews:

Related manuals for WMO1-G900

Brands by name

Popular brands

Wavecom WMO1-G900, User Manual

Search results

Summary of Contents for WMO1-G900

Reviews:

Related manuals for WMO1-G900

Brands by name

Popular brands