Wavecom WMO1-G900 User Manual Download Page 44

Page: 44 / 67

Wavecom GSM Modem

This confidential document is the property of WAVECOM and may not be copied or circulated without permission

7. AT commands for data

7.1. Bearer type selCBST

The syntax of the command is AT+CBST=<speed>,0,<ce>

The selection of the bearer impacts both incoming and outgoing calls.

No data compression is provided and only asynchronous modem is
supported.

<speed>

Modem type

transmission mode

0 :autobauding

None

asynchronous MODEM

4 :2400 bps,

V22bis

asynchronous MODEM

5 :2400 bps

V26ter

asynchronous MODEM

6 :4800 bps

V32

asynchronous MODEM

7 :9600 bps

V32

asynchronous MODEM

68 :2400 bps

V110

asynchronous MODEM

70 :4800 bps

V110

asynchronous MODEM

71 :9600 bps

V110

asynchronous MODEM

<ce>

connection element

Transparent only

Non transparent only

100

Transparent preferred

101

Non transparent preferred

Application to GSM

AT+CBST=7,0,1

ask for a bearer

GSM to application

bearer supported

Application to GSM

AT+CBST=81,0,0

ask for a bearer

Summary of Contents for WMO1-G900




































































Search results

Summary of Contents for WMO1-G900

Reviews:

Related manuals for WMO1-G900

Brands by name

Popular brands

Wavecom WMO1-G900, User Manual

Search results

Summary of Contents for WMO1-G900

Reviews:

Related manuals for WMO1-G900

Brands by name

Popular brands