Wavecom W-CLOUD Manual Download Page 18

Page: 18 / 381



General Information

WAVECOM Decoder W74PC, W-PCI/e, W-CODE, W-CLOUD Manual V9.1.0

Version

Date

Changes

Dedicated phase plane for MIL/STANAG modes to show the PSK signal be-

fore and after the equalizer.

MIL-188-110A can now be synchronized on the probe: on-going synchroni-

zation.

DMR has a bit-transparent output (Options -> Message Type).

XML RCI extension: add commands to retrieve CCC mode table.

XML RCI extension: classifer result message is delivered in a better struc-

ture. Details refer to XML RCI Manual.

8.5.0

15-March-2014

New mode MIL-188-110A-MOD.

New modes THROB and THROBX.

Significant enhancement of DMR: both slots are decoded. Full monitoring

especially of communication with a base station.

Bit transparent output for dPMR (Options -> Message Type).

XMLTestGUI.exe is released in XML RCI SDK for user to run W-CODE with-

out Wavecom GUI.

General improvements and bug fixes.

8.5.1

03-June-2014

New identity for Wavecom hardware decoders. W74PC, W-PCI and W-PCIe

appear with their own logo. W74PC, W-PCI and W-PCIe run with an in-card

license. The USB dongle license is no longer necessary.

8.6.0

03-Nov-2014

TETRA SNDCP output.

New mode CLOVER-2500.

INMARSAT-MINI-M now supports HSD (M4): SAT-B-C-HSD and SAT-mM-C-

HSD.

Enhancement of PACTOR-I: all connect frames and free signals are decod-

ed.

Enhancement of PACTOR-II and PACTOR-III: able to decode encrypted

connections.

8.7.0

16-May-2015

SAT-Aero modes: SAT-AERO-P, SAT-AERO-C, SAT-AERO-R and SAT-AERO-

DMR revisited: two new SYNC types according to ETSI TS 102 361-1 V2.1.1

(2012-4). Protocol Tier I, II and III update according to ETSI TS.

Improve the “Device Selector” GUI for HW decoder. Add “License Edit” but-

ton.

Add “live-sound-mute” parameter (for DMR, dPMR modes etc.) into XML

RCI interface.

Custom input supports VITA-49 protocol.

General improvements and bug fixes.

8.8.0

10-Feb-2016

Revision MIL-188-141B.

General revision of most MIL / STANAG modes.

Soft decision in MFSK-8 and MFSK-16 modes. Display “Confidence”.

Phase Plane extension: display trace between two neighbour symbols.

Voice session saved in NXDN mode.

Enhanced ACARS protocol interpreter.

New XML message indicating the release version number, e.g., 8.8.0.

New XML message “License error: Selected mode is not licensed for the se-
lected device” when calling VHF/UHF CCC without proper license. This is on-

ly available in W-CODE.

Wibu SD card as new license carrier. USB dongle (CmStick/C) still available.

Summary of Contents for W-CLOUD






























































































































































































































































































































































































Search results

Summary of Contents for W-CLOUD

Reviews:

Related manuals for W-CLOUD

Brands by name

Popular brands

Wavecom W-CLOUD, Manual

Search results

Summary of Contents for W-CLOUD

Reviews:

Related manuals for W-CLOUD

Brands by name

Popular brands