Wavecom W-CLOUD Manual Download Page 197 | Manualshive

Page: 197 / 381

background image

WAVECOM Decoder W74PC, W-PCI/e, W-CODE, W-CLOUD Manual V9.1.0

Transmission Modes



187

Parameter

Value

Center frequency

1760 Hz

Receiver settings

DATA, CW, LSB or USB

Input format(s)

AF, IF

BINARY, HEX and ASCII output are provided.

MIL-188-110-39Tone, (MIL-188-110A/B Appendix C)

MIL-STD-188-110 39 Tone is a non-mandatory part of the MIL-STD-188-110 military standard for use by
all departments and agencies of the Department of Defense.

Parameter

Value

Frequency range

HF

Operation modes

PSK, Simplex

Modulation

39 tone Q-DPSK

Symbol rate

44.44 Bd

Center frequency

1800 Hz

Receiver settings

DATA, CW, LSB or USB

Input format(s)

AF, IF

Definition

The modulation technique used in this mode consists of differential quadrature phase shift keying (QDPSK)
of 39 orthogonal sub carriers in the range from 675Hz to 2812.5 Hz, and an additional unmodulated Dop-
pler reference tone at 393.75Hz.

The modulation speed (symbol rate) is always 44.44 Bd. Through the transmission of redundant infor-
mation on certain tones, different user data rates can be achieved within a range of 75 to 2400 bps.

This mode uses FEC and interleaving to combat the effects of fading, frequency shift, multipath, and burst
noise.

The user data is transmitted using a continuous frame structure with a variable block length (number of
symbols), depending on user data rate and message type.

Each transmission starts with a preamble, consisting of three phases, followed by block synchronization
and data segments. The data block immediately follows the next block synchronization segment defining
again the start of the next data block. This repeated frame structure enables synchronization of the de-
modulator at any time of transmission.

The end of transmission is determined by an EOM sequence (at least ten ones "1").

Data Display

There are two different types of data transmissions - synchronous and asynchronous.

In the synchronous data mode, the data is bit synchronously displayed as 7 bit characters, while in the
asynchronous mode, different character lengths are possible using start, stop and parity bits. The parity,

«
...
195
196
197
198
199
...
»

Summary of Contents for W-CLOUD






























































































































































































































































































































































































Reviews:

No comments

Related manuals for W-CLOUD

Brand: Magnum Energy Pages: 2

Brand: Magnum Energy Pages: 62

Brand: IAdea Pages: 4

Brand: INTECNO Pages: 16

Brand: Mitsubishi Pages: 106

Brand: V2 Pages: 48

Brand: Sigineer Power Pages: 39

Brand: Vacon Pages: 44

Auto-Link-SPE-G

Brand: I-novative Pages: 10

Brand: Suaoki Pages: 32

Brand: Speaka Professional Pages: 8

Brand: SIIG Pages: 32

Brand: J-Tech Digital Pages: 8

TFC-1000S70 - DATA SHEETS

Brand: TRENDnet Pages: 1

XPower Mobile Plug 75

Brand: Xantrex Pages: 2

Brand: Inter-m Pages: 15

Brand: Transition Networks Pages: 5

Brand: Transition Networks Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands