Watts scientific CLX-Ex A28031 Operation And Maintenance Manual Download Page 22

Page: 22 / 24

Accessory

Catalog Number

Photo

Check Valve Flushing Kit

25096

T-Strainer/ Pressure Regulator Assembly

25357

Replacement T-Strainer Screen

28625

Water Intake Assembly

28411

12.0 Accessories and Replacement Parts List (Cont’d)

The items shown below are recommended accessories and replacement parts.

To order any accessory or replacement part, please contact the HF scientific Customer Service Department. If for any reason technical assistance is

needed regarding this instrument, please do not hesitate to contact the HF scientific Technical Services Department.

HF scientific

16260 Airport Park Drive, Suite 140

Fort Myers, FL 33913

Phone: 239-337-2116

Toll Free: 888-203-7248

Fax: 239-454-0694

Email: [email protected]

Website: www.hfscientific.com

Summary of Contents for scientific CLX-Ex A28031

























Search results

Summary of Contents for scientific CLX-Ex A28031

Reviews:

Related manuals for scientific CLX-Ex A28031

Brands by name

Popular brands

Watts scientific CLX-Ex A28031, Operation And Maintenance Manual

Search results

Summary of Contents for scientific CLX-Ex A28031

Reviews:

Related manuals for scientific CLX-Ex A28031

Brands by name

Popular brands