Watts PVi CENTURION Installation, Operation And Maintenance Manual Download Page 33

Page: 33 / 131

Centurion Water Heater- Edge [ii]: Install-Operation-Service

SECTION 2: INSTALLATION

OMM-0153_A

• 8/25/2022 Technical Support • (800) 526-0288 • Mon-Fri, 8 am - 5 pm EST Page 33 of 131

Once system load is satisfied and all Client units have stopped firing, the WHM Manager opens
the Sequencing Valves of units specified in

Min Unit

settings in

Main Menu

→

Advanced

Setup

→

WHM Cascade

→

Cascade Comm

The implementation of WHM, and the installation and use of this valve, is optional. However,

when WHM is implemented

use of this valve is

strongly recommended

Installation consists of installing the Sequencing Valve in the hot water outlet pipe, and then
connecting it to the pre-wired connector on the shell harness, as described below.

NOTE:

The pre-programmed Sequencing Valve control is installed on Water Heaters that are

part of a Water Heater Management (WHM) group. Refer to Section SECTION 8: for
instructions.

WHM Sequencing Isolation Valve Installation:

1. Remove the Sequencing Isolation Valve from the shipping container.

2. Attach valve to the water outlet of the unit using the pipe union and nipple provided.

3. Ensure valve is positioned with the actuator enclosure position as shown in Figure 2-17:

Sequencing Valve Installation.

4. PVI recommends that another pipe nipple and flange be attached to the valve inlet prior to

connecting the water piping.

5. Tighten all pipe connections after the valve is properly positioned.

6. Connect the 5-pin Molex connector on the valve to the mating connector on the

CENTURION harness at the rear of the unit.

Figure 2-17: Sequencing Valve Installation

Sequencing
Isolation
Valve

Summary of Contents for PVi CENTURION




































































































































Search results

Summary of Contents for PVi CENTURION

Reviews:

Related manuals for PVi CENTURION

Brands by name

Popular brands

Watts PVi CENTURION, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for PVi CENTURION

Reviews:

Related manuals for PVi CENTURION

Brands by name

Popular brands