Watts PVi CENTURION Installation, Operation And Maintenance Manual Download Page 66 | Manualshive

Page: 66 / 131

background image

Centurion Water Heater- Edge [ii]: Install-Operation-Service

SECTION 7: MAINTENANCE

OMM-0153_A

• 8/25/2022 Technical Support • (800) 526-0288 • Mon-Fri, 8 am - 5 pm EST Page 66 of 131

SECTION 7:

MAINTENANCE

7.1 MAINTENANCE SCHEDULE

All CENTURION Water Heaters require regular routine maintenance to keep up efficiency and
reliability. For best operation and life of the unit, the following routine maintenance procedures
should be performed in the time periods specified in the table below. For a complete inspection
check list see ASME CSD-1 chart.

W A R N I N G !

Prior to servicing, ensure that the following guidelines are strictly observed:

● Follow all Lockout/Tagout protocols in effect at the site.

● Disconnect power supply by turning off the service switch and AC supply circuit breaker.

● Shut off gas supply at the manual shut-off valve provided with the unit.

● Allow the unit to cool to a safe water temperature to prevent burning or scalding.

Maintenance Schedule

SEC

ITEM

6 MOS. *

12 MOS.

24 MOS.

LABOR
TIME

7.2

Igniter-Injector

Inspect

Inspect, replace if
necessary

Replace

15 mins.

7.3

Flame Detector

Inspect

Inspect, replace if
necessary

Replace

15 mins.

7.4

O

2

Sensor inspection and

calibration

Inspect

Inspect/Clean/
Calibrate

15 mins.

5.4

Combustion Calibration

Check

Check

1 hr.

7.5

Testing of Safety Devices

See ASME
CSD-1 Chart

45 mins.

7.6

Burner

Inspect

2 hrs.

7.8

Condensate Drain Trap

Inspect

Inspect, Clean &
Replace Gaskets

Inspect, Clean &
Replace Gaskets

30 mins.

7.8

Air Filter

Clean

Replace

15 mins.

7.9

Isolation Valve

Check

7.10

Recirculation Pump

Check

7.12

Periodic Testing

Routine verification of functionality, various schedule

* Only performed after initial 6-month period after initial startup.

The following maintenance kits are available from PVI. All kits include a Technical Instruction
Document (TID) with instructions for performing the tasks specified.

Maintenance Kits

Model

Kit#

Parts Serviced/Replaced

Doc Name

12 Month Maintenance Kit
CEN2000

58025-25

Ignitor, Flame Rod, Condensate trap O rings

TID-

0236

24 Month Maintenance Kit

CEN2000

58025-26

Burner & Blower gaskets, LWCO, air filter replacement

TID-

0237

58025-27

Burner & Blower gaskets, LWCO, air filter

cleaner

«
...
64
65
66
67
68
...
»

Summary of Contents for PVi CENTURION




































































































































Reviews:

No comments

Related manuals for PVi CENTURION

Brand: Marta Pages: 12

Brand: Lasko Pages: 4

Brand: Lasko Pages: 4

aroSTOR VWL B 200/5 UK

Brand: Vaillant Pages: 24

Brand: Vaillant Pages: 20

Brand: Vaillant Pages: 24

Brand: Zip Pages: 12

Brand: WaterCare Pages: 7

JABSCO 11860 Series

Brand: Xylem Pages: 24

Brand: Calpeda Pages: 27

Brand: Watts Pages: 12

Brand: Gude Pages: 62

Brand: Harvia Pages: 44

Brand: Watts Pages: 73

Brand: Wacker Neuson Pages: 70

20:1 KING 231131

Brand: Graco Pages: 18

Brand: OSO Pages: 16

Brand: Reality Leuchten Pages: 86

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands