background image

19

Controller Features 

Remote Lock

The controller does not allow the unit/system to go into 

Regeneration until the Regeneration Lockout Input signal to the 

unit is cleared. This requires a contact closure to activate the 

unit. The recommended gauge wire is 16 AWG with a maximum 

wire length run of 50 feet.

Regeneration Day Override Feature

If the Day Override option is turned on and the valve reaches the 

set Regeneration Day Override value, the Regeneration Cycle 

starts if no other unit is in Regeneration. If other units are in 

regeneration, it is added to a regeneration queue. This occurs 

regardless of the remaining volume available.

Lock Settings (access to Master Programming)

Lock Settings prevents the user from accessing Master 

Programming. In Master Programming, select the desired Lock 

Settings option (Off, Time Based, Delayed, or Enter Code).

Time Based -

 User must set clock to 12:01 pm to unlock

Delayed -

 User must press and hold the Left and Down buttons 

for 60 continuous seconds to unlock

Enter Code -

 User must input code “1201” to unlock

Capacitive Buttons

Capacitive button entry warrant different consideration than 

tactile button entry. Do not wear gloves. Be sure to keep your 

hands and the capacitive buttons free of debris, grease, or water. 

Buttons may become temporarily unresponsive if environmen-

tal conditions change such as sudden humidity or temperature 

changes. If buttons become unresponsive, wait 5 to 10 minutes 

for the buttons to recalibrate.

LED Status indicator

Blue - Unit in Service
Flashing Blue - Regeneration Queued
Green - Unit in Regeneration
Flashing Green - Unit in Standby
Red - Error with codes

Power Loss Backup

Time of day super capacitor backup for power loss; rated to last 

minimum 12 hours

Continuous Flow Detect

Alert appears when specified continuous flow rate is detected 

during service over a specified duration. Continuous flow rate is 

adjustable from 0.1 to 99999.9 GPM/LPM (accuracy of flow rate 

detected will vary based on capability of meter). Duration range is 

adjustable from 1 to 255 hours.

Remote Regeneration

Ability to trigger a regeneration via a remote input.

Regeneration Types

Softener/Filter Meter Delayed -

 When volume remaining 

reaches zero and the scheduled regeneration time is reached 

(default 2 a.m. softener; 12 a.m. filter), the unit will regenerate.

Softener/Filter Meter Immediate - 

When volume remaining 

reaches zero, the unit will regenerate.

Time Clock -

 Once volume remaining reached zero and the 

selected regeneration time is reached (default 2 a.m. softener;  

12 a.m. filter), the unit will regenerate. 

Day of the Week -

 Once volume remaining reaches zero and 

the selected Day of the Week is reached, the unit will regenerate. 

Remote Regeneration -

 Remote Regeneration is accomplished 

by a 3rd party device completing a contact closure connected 

to the remote regeneration input connector. The 3rd party device 

must complete the signal duration time that was set in the dura-

tion signal time in programming to start a regeneration. You 

can set the remote regeneration for immediate regeneration or 

delayed regeneration at the set time that was programmed for 

regeneration time in programming.

Reset to Factory Defaults

While powering up the unit, when the Pentair Diamond logo

®

 

logo appears, press and hold the Extra Cycle button to access 

the Reset menu then select Reset to Factory Defaults. Press the 

Extra Cycle Button to confirm your selection and to advance to 

the service screen. Furthermore, you may select Reset to Non-

Factory Defaults to save a set of unique control parameters.

Power on the unit. When Pentair logo appears, press 
and hold the Extra Cycle button. The Reset menu 
appears.

Use the up/down buttons to select. 

Press the Extra Cycle button to set the desired option 
and return to the Service screen.

Lock Window

Lock Window prevents the unit from regenerating during a specified 

time frame. Two lock windows are available (Lock Window #1 and 

Lock Window #2). In Master Programming, enable a Lock Window 

then select the desired Lock Start time and Lock End time.

Settings Review

To prevent unintentional changes to Master Programming, 

enable Settings Review to view and navigate through Master 

Programming settings without the ability to edit.

The Pentair Diamond logo

®

 is a trademark owned by Pentair plc or its affiliates.

Summary of Contents for HC-200 Series













































Reviews: